Flat tappet lifter failure

[Paul Precht]

Originally Posted by Gmirza

I lost one cam lobe, I noticed it after about 100 runs. I’m not sure when it went away. Most likely caused by lack of oiling at low rpm. From what I’ve been told the tool steel lifter, cast cam combination is only good for maybe 200 runs if you’re lucky. Go fast stuff can a P.I.T.A.

Hi George, do you know what your spring pressures were open and closed.

[Gmirza]

Originally Posted by Paul Precht

Hi George, do you know what your spring pressures were open and closed.

Hi Paul,
I’m not sure. I didn’t check them.

[Bench Racer]

Terry you have a PM

[Terry Cain]

https://rehermorrison.com/tech-talk-...-flat-tappets/

[Billy Nees]

Originally Posted by Terry Cain

https://rehermorrison.com/tech-talk-...-flat-tappets/

What's your point. If you want to use a roller cam then either run SS or build a newer Corvette Stocker!

[john ancona]

The point is many on here have the same canned suggestions , many miss the facts of which there are many, I ,and others have went through all of them many times in the past.

If I just take two rule changes of which were many over the years that have led up to now which are the roller rockers ,and the valve springs ,I am hard pressed to remember nattering nabobs of negativism when those two rule changes were made as to what a few say will eliminate stock as if they even know ,rather that focus on the cost of stock eliminator cars of today' along with the fact of the age of the cars 50 plus years in some cases ,along with the ages of many of the racers that drive them a few on here seem to only be interested in casting there unwanted opinions .

Everyone should have a say as to what they want to run , while we still can if we stay on the course of the way it is in stock very soon there will be no more stock because of the cost, and lack of the parts we need, not the lifters ,here are two strong indicators as to why Electric cars ,but even worse eBay facing fines of $1.9 Billion for allowing the sale of parts that violate the clean air act .
If you think well it won't effect me you're wrong .Already vendors are scared to ship parts , even oil to certain states.

[1347]

As I was in teardown at the Keystones, a D1 racer had Lonnie's ear about a multitude of topics, among them were roller lifters. I am not to tell you what that racers stance was on them, but I will tell you Lonnies take on it. Lonnie said he is not gonna open that door and allow them. He said as soon as he did that, many racers would be buying new roller profile cams, and would open a whole cost to the sport. I think those who are waiting for the rule to change should come up with another plan, whatever that may be.

[HP HUNTER]

Originally Posted by john ancona

The point is many on here have the same canned suggestions , many miss the facts of which there are many, I ,and others have went through all of them many times in the past.

If I just take two rule changes of which were many over the years that have led up to now which are the roller rockers ,and the valve springs ,I am hard pressed to remember nattering nabobs of negativism when those two rule changes were made as to what a few say will eliminate stock as if they even know ,rather that focus on the cost of stock eliminator cars of today' along with the fact of the age of the cars 50 plus years in some cases ,along with the ages of many of the racers that drive them a few on here seem to only be interested in casting there unwanted opinions .

Everyone should have a say as to what they want to run , while we still can if we stay on the course of the way it is in stock very soon there will be no more stock because of the cost, and lack of the parts we need, not the lifters ,here are two strong indicators as to why Electric cars ,but even worse eBay facing fines of $1.9 Billion for allowing the sale of parts that violate the clean air act .
If you think well it won't effect me you're wrong .Already vendors are scared to ship parts , even oil to certain states.

You need to get out of Covina and move into my neighborhood, we can use some one like you. Oak Crest Georgetown Tx, ck it out.........