|
|
09-25-2024, 08:34 AM
|
#1 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Square 10
It begins
|
|
|
|
09-25-2024, 09:26 AM
|
#2 |
|
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 2,628
Likes: 160
Liked 759 Times in 379 Posts
|
Re: Square 10
Always enjoy the photo documentary of your builds.
|
|
|
|
| Liked |
|
09-25-2024, 11:57 AM
|
#3 | |
|
Member
Join Date: May 2011
Location: Auburndale,Florida
Posts: 220
Likes: 29
Liked 71 Times in 38 Posts
|
Re: Square 10
Quote:
|
|
|
|
|
|
09-25-2024, 05:09 PM
|
#4 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Re: Square 10
the core
|
|
|
|
| Liked |
|
09-25-2024, 05:11 PM
|
#5 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Re: Square 10
Mark,
The wheels are Billet Specialties Winlite. I like them, they are very well done, look great. I like shiny parts 
|
|
|
|
| Liked |
|
09-25-2024, 05:13 PM
|
#6 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Re: Square 10
Mark, 15 x 4 front and 15 x 14 rear. And off all things, the center cap is machined on the wheel, all one piece, non-removable.
|
|
|
|
|
09-25-2024, 05:18 PM
|
#7 | |
|
Member
Join Date: May 2011
Location: Auburndale,Florida
Posts: 220
Likes: 29
Liked 71 Times in 38 Posts
|
Re: Square 10
Quote:
|
|
|
|
|
|
09-25-2024, 05:30 PM
|
#8 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Re: Square 10
Mark, you will notice the rear housing has overlength tubes. This allows you to cut and fit the wheel/tire package exactly where you want it in the chassis. The rear wheels are 4.5 back spacing.
|
|
|
|
|
09-25-2024, 06:57 PM
|
#9 | |
|
Member
Join Date: May 2011
Location: Auburndale,Florida
Posts: 220
Likes: 29
Liked 71 Times in 38 Posts
|
Re: Square 10
Quote:
|
|
|
|
|
|
10-05-2024, 08:39 AM
|
#10 |
|
Senior Member
Join Date: Sep 2006
Location: Kilgore TX
Posts: 519
Likes: 8
Liked 225 Times in 90 Posts
|
Re: Square 10
I will move around from one area to another. About 85% of the parts needed to complete the projects are on hand.
*Setting cam timing *Checking valve to piston clearance *Over the years, I have tested many carbs. One company that consistently provides good service and results is APD. The Square 10 will carry a complete APD methanol system. *High compression is my friend. *This is the first time posting about my experimental 2/16 offset stud. |
|
|
|
| Liked |
 |
|
|
Linear Mode
