Axle preference ??? - Page 2

Kegracing · 07-20-2008, 05:27 PM

I broke a set of 33 spline strange axles in a 10 sec. car, footbraking, a few years ago. The axles were less than 2 years old, but Strange refused to replace because I was not the origional buyer, even though I had the bill of sale.

Replaced with Moser. Everything looked and fit well. About 2 years later, broke wheel studs at Nat. event in Richmond (probably my fault, used impact gun all the time). Went to the Moser trailer to buy some. Told them what happened, and that I needed to buy some studs. Lady working there gave me two packages, no cost, and told me to come get them if I needed any help!

Probably 500 passes later, with no issues at all, sold the car.

Great product and customer service... Look what Moser gives back to the racers, with their IHRA shootouts.

While I feel MW's has good stuff, is it any better?

I like to support those that support me!

Moser for me.

good luck!

Dyno · 07-20-2008, 09:59 PM

Mark Williams in 4 different cars, never a problem. The fit, finish and quality stand out when you compare the other brands side by side. I have had friends that have twisted Strange stuff all the time. Buy the best, Mark Williams, and you never have to worry about it. Dyno

tim worner · 07-21-2008, 05:14 PM

Car built in 1986 with M/W and still going strong. I can only guess that there are over a thousand runs on them. M/W is one of the first checks that you will receive for contingency. Plus they are at National events if you need something. Get the best set up they have first and you're done.

tgw323 · 07-22-2008, 06:08 AM

I've seen more broken Strange axles than anything, including stock. MW for me.

Shawn Blair · 07-22-2008, 04:19 PM

M/W for me also. Very high quality. Put them in and forget about them!

Bunkster · 07-23-2008, 03:26 PM

Quote:

Originally Posted by tgw323

I've seen more broken Strange axles than anything, including stock. MW for me.

I am certain my memory is correct when I recall Al Provoast, with his N/SA 403 wagon, broke a 35 spline Strange axle: And 35 spline stuff, of anyone's manufacture, is HUGE when compared to stock.

Paul Merolla · 07-23-2008, 04:33 PM

Great...wish I'd have asked around before buying the Strange axles and spool that are waiting to go in.

07-20-2008, 05:27 PM	#11
Kegracing Member Join Date: Jun 2002 Location: Red Oak, TX Posts: 441 Likes: 0 Liked 0 Times in 0 Posts	Re: Axle preference ??? I broke a set of 33 spline strange axles in a 10 sec. car, footbraking, a few years ago. The axles were less than 2 years old, but Strange refused to replace because I was not the origional buyer, even though I had the bill of sale. Replaced with Moser. Everything looked and fit well. About 2 years later, broke wheel studs at Nat. event in Richmond (probably my fault, used impact gun all the time). Went to the Moser trailer to buy some. Told them what happened, and that I needed to buy some studs. Lady working there gave me two packages, no cost, and told me to come get them if I needed any help! Probably 500 passes later, with no issues at all, sold the car. Great product and customer service... Look what Moser gives back to the racers, with their IHRA shootouts. While I feel MW's has good stuff, is it any better? I like to support those that support me! Moser for me. good luck!

07-20-2008, 09:59 PM	#12
Dyno Senior Member Join Date: Dec 2002 Posts: 918 Likes: 1,140 Liked 693 Times in 205 Posts	Re: Axle preference ??? Mark Williams in 4 different cars, never a problem. The fit, finish and quality stand out when you compare the other brands side by side. I have had friends that have twisted Strange stuff all the time. Buy the best, Mark Williams, and you never have to worry about it. Dyno

07-21-2008, 05:14 PM	#13
tim worner Senior Member Join Date: Jan 2002 Location: duncannon Posts: 837 Likes: 14 Liked 126 Times in 20 Posts	Re: Axle preference ??? Car built in 1986 with M/W and still going strong. I can only guess that there are over a thousand runs on them. M/W is one of the first checks that you will receive for contingency. Plus they are at National events if you need something. Get the best set up they have first and you're done. __________________ Tim Worner SS 1747

07-22-2008, 06:08 AM	#14
tgw323 Junior Member Join Date: Jul 2008 Posts: 1 Likes: 0 Liked 0 Times in 0 Posts	Re: Axle preference ??? I've seen more broken Strange axles than anything, including stock. MW for me.

07-22-2008, 04:19 PM	#15
Shawn Blair Member Join Date: Dec 2007 Location: Everson, WA. Posts: 122 Likes: 1 Liked 0 Times in 0 Posts	Re: Axle preference ??? M/W for me also. Very high quality. Put them in and forget about them!

07-23-2008, 04:33 PM	#17
Paul Merolla Senior Member Join Date: Dec 2001 Location: Papillion, NE Posts: 611 Likes: 242 Liked 293 Times in 65 Posts	Re: Axle preference ??? Great...wish I'd have asked around before buying the Strange axles and spool that are waiting to go in.