HOME FORUM RULES CONTACT
     
   
   

Go Back   CLASS RACER FORUM > Class Racer Forums > Stock and Super Stock Tech
Register Photo Gallery FAQ Community Calendar

Reply
 
Thread Tools Display Modes
Old 04-14-2020, 07:28 PM   #1
Frank Castros
VIP Member
 
Join Date: Nov 2001
Location: The Lowcountry.
Posts: 2,961
Likes: 2,550
Liked 2,699 Times in 952 Posts
Default Re: Stock Eliminator Cylinder Heads

Quote:
Originally Posted by Alan Nyhus View Post
A very well done set of SBC Stock Eliminator heads that perform and pass tech are easily $4,500. An intake done to match can be $1000-1500. -Al
Think about the core issues of this discussion. Stock? What?

Last edited by Frank Castros; 04-15-2020 at 11:20 AM.
Frank Castros is offline   Reply With Quote
Liked
Old 04-14-2020, 09:15 PM   #2
Alan Nyhus
VIP Member
 
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,180
Likes: 1,074
Liked 799 Times in 236 Posts
Default Re: Stock Eliminator Cylinder Heads

Quote:
Originally Posted by Frank Castros View Post
Thing above the core issues of this discussion. Stock? What?
Well, the title of the thread is: Stock Eliminator Cylinder Heads

And the question was asked by Andy:

Quote:
Originally Posted by Andy Friar View Post
What STK combo(s) are the heads and manifold $5500? I am assuming at that cost they are built up and installed, correct?
__________________
"That'll never work....."
Alan Nyhus is offline   Reply With Quote
Old 04-14-2020, 10:31 PM   #3
Greg Reimer 7376
VIP Member
 
Join Date: Nov 2008
Location: Glendora,Calif.
Posts: 1,135
Likes: 172
Liked 704 Times in 218 Posts
Cool Re: Stock Eliminator Cylinder Heads

One of the reasons for the cost, besides its for the price that horsepower comes with, is that it is very labor intensive work. You almost can't charge for what its worth because of the expense of doing it. A set of heads is as much work as doing the rest of the bottom half of the engine. If a bottom end failure does in the short block, cam, pan and related items, that's pretty seriously bad enough. When one or both heads gets hurt, that adds to it or doubles the equation, in both dollar value of pieces, but in time spent above and beyond that. Also, like everything else that is cast iron, variations in castings from the foundry onward, will result in a part being just OK, a Better part or a Good part. One out of every 10 or 20 might be an Excellent casting, which means its better to start with. Before all the incredible head work and intake work came into being, racers used to flow bench test sometimes 20 heads, and kept track of the variables. Out of the 20, enough variations were obvious in that two heads were over and above the rest of them, those became the best performing pair of the bunch, justifying the further money that was going to be spent on them. The rest probably wound up in the ads somewhere. The newest technology applied to heads tends to result in more heads being acceptable,since the necessary work will tend to equalize them with the top of the line head a little more. Variations in castings can even be traced to foundry data and date codes and that sort of thing. Lots of builders know what further numbers on a given set of heads to look for, all 041's or 462's or 290's aren't always equal. Cylinder heads are a whole art form in engine building that takes this sport to an unforeseen level.
Greg Reimer 7376 is offline   Reply With Quote
Old 04-15-2020, 06:55 PM   #4
Alan Nyhus
VIP Member
 
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,180
Likes: 1,074
Liked 799 Times in 236 Posts
Default Re: Stock Eliminator Cylinder Heads

Quote:
Originally Posted by Frank Castros View Post
Think about the core issues of this discussion. Stock? What?
Hi Frank.

Thanks for editing your original post to clarify. Makes more sense to me, now. -Al
__________________
"That'll never work....."
Alan Nyhus is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:39 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.