327 SS Bowtie Shortblock & Parts

mweb · 02-06-2010, 01:14 PM

GM Bowtie block, 4.060" finished bore, C-K 10 plate honed, ARP head studs installed, .843" bronze lifter bushings (LSM) installed (honed to size for Crower Cut-Away Severe Duty lifters), LSM 55mm cam tunnel w/slider bearings installed & fitted to LSM camshaft, steel billet 4-bolt main caps installed on 3 center mains, block align-honed (sunnen machine). China wall milled .135", decked for 327 SS application (.015" Fel-Pro gasket required), block face clearanced for Jesel cover, deck pins installed.

Moroso rear seal adapter included.

327 cast crank .010"/.030" stroked .015" & all strokes indexed.

Clevite rod & main bearings (crank ground to correct clearances).

Manley 5.7" superstock rods w/cap screw bolts.

Wiseco pistons (10 pistons) slipper skirt design, coated skirts. No top ring groove, no valve pockets. Pistons are pin-fitted to Patterson tool steel wrist pins.

Speed-Pro R-20100 +.065" .043"/.043"/3/16ths"

Patterson tool steel wrist pins .927" X 2.500" X .120" wall.

LSM 55mm camshaft 280/.440" int., 284/.450 exhaust 107 l/c
4/7 swap firing order.

Crower Cut-Away Severe Duty roller lifters, fitted to lifter bores.

All parts above are new in the box. $5000 for everything.

Also have:
Jesel Belt Drive (SBC) w/new upper seal plate & new belt (still in plastic packages), new Garlock lower seal. $600 w/above shortblock or after shortblock sells.

Jesel Pro Series Shaft Rocker Set KRA-04401 for above 327.
1.8 Int./1.7 Ex. New in the box w/all parts. Will sell w or w/o motor.
$1050

SBC head castings:
1 pr. 3917293
1 pr. 3817291
1 pr. 3890462
All castings are good take-offs. $60/pair

1 SBC Intake manifold 3919803 $50.00

Buyer pays shipping.

Michael Kilduff · 02-06-2010, 02:14 PM

PM sent

tj310 · 02-06-2010, 06:49 PM

Whereabouts are you? Thanx Trevor

02-06-2010, 01:14 PM	#1
mweb Junior Member Join Date: Jul 2009 Posts: 6 Likes: 0 Liked 0 Times in 0 Posts	327 SS Bowtie Shortblock & Parts GM Bowtie block, 4.060" finished bore, C-K 10 plate honed, ARP head studs installed, .843" bronze lifter bushings (LSM) installed (honed to size for Crower Cut-Away Severe Duty lifters), LSM 55mm cam tunnel w/slider bearings installed & fitted to LSM camshaft, steel billet 4-bolt main caps installed on 3 center mains, block align-honed (sunnen machine). China wall milled .135", decked for 327 SS application (.015" Fel-Pro gasket required), block face clearanced for Jesel cover, deck pins installed. Moroso rear seal adapter included. 327 cast crank .010"/.030" stroked .015" & all strokes indexed. Clevite rod & main bearings (crank ground to correct clearances). Manley 5.7" superstock rods w/cap screw bolts. Wiseco pistons (10 pistons) slipper skirt design, coated skirts. No top ring groove, no valve pockets. Pistons are pin-fitted to Patterson tool steel wrist pins. Speed-Pro R-20100 +.065" .043"/.043"/3/16ths" Patterson tool steel wrist pins .927" X 2.500" X .120" wall. LSM 55mm camshaft 280/.440" int., 284/.450 exhaust 107 l/c 4/7 swap firing order. Crower Cut-Away Severe Duty roller lifters, fitted to lifter bores. All parts above are new in the box. $5000 for everything. Also have: Jesel Belt Drive (SBC) w/new upper seal plate & new belt (still in plastic packages), new Garlock lower seal. $600 w/above shortblock or after shortblock sells. Jesel Pro Series Shaft Rocker Set KRA-04401 for above 327. 1.8 Int./1.7 Ex. New in the box w/all parts. Will sell w or w/o motor. $1050 SBC head castings: 1 pr. 3917293 1 pr. 3817291 1 pr. 3890462 All castings are good take-offs. $60/pair 1 SBC Intake manifold 3919803 $50.00 Buyer pays shipping.

02-06-2010, 02:14 PM	#2
Michael Kilduff Member Join Date: Sep 2008 Location: Carolina Beach, NC Posts: 281 Likes: 0 Liked 0 Times in 0 Posts	Re: 327 SS Bowtie Shortblock & Parts PM sent

02-06-2010, 06:49 PM	#3
tj310 Member Join Date: Sep 2009 Location: Dresden On. Canada Posts: 460 Likes: 0 Liked 0 Times in 0 Posts	Re: 327 SS Bowtie Shortblock & Parts Whereabouts are you? Thanx Trevor