|
|
|
|
08-24-2021, 08:18 AM
|
#1 |
|
VIP Member
Join Date: Jun 2007
Location: Northern New Jersey suburbs
Posts: 2,314
Likes: 25
Liked 544 Times in 213 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
I've been reading this thread and wondered why no one mentioned detonation as being a possible issue.
It can show up in rod bearings.... Usually the shells just fall out....and might have some odd looking wear marks....
__________________
Rich Biebel S/C 1479 Stock 147R |
|
|
| Liked |
|
08-24-2021, 11:21 AM
|
#2 | |
|
Senior Member
Join Date: Sep 2006
Location: Fulton County, PA
Posts: 614
Likes: 16
Liked 920 Times in 259 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
Quote:
Fly poop on spark plugs? Fuel change? Verify timing and TDC marks? Try another known good timing light? Just reaching here. |
|
|
|
|
|
08-24-2021, 11:29 AM
|
#3 | |
|
VIP Member
Join Date: Oct 2002
Location: On a hilltop in Pa.
Posts: 4,494
Likes: 3,596
Liked 7,732 Times in 1,739 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
Quote:
__________________
Billy Nees 1188 STK, SS I'm not spending 100K to win 2K |
|
|
|
|
|
08-24-2021, 12:32 PM
|
#4 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,640
Likes: 1,937
Liked 10,712 Times in 2,230 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
First noticed it when we started getting close to the 590 hp number. Damper is on TDC, fuel seems to make no difference c11, c12, c10, renegade 116. cam changed made no difference.
|
|
|
|
|
08-24-2021, 02:00 PM
|
#5 |
|
VIP Member
Join Date: Jun 2007
Location: Northern New Jersey suburbs
Posts: 2,314
Likes: 25
Liked 544 Times in 213 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
If the engine is apart and obviously it is....
Look at the ring lands and the tops of the pistons for any oddball signs that usually indicate detonation. Pecker tracks on pistons, or on the sides of the pistons above the rings. Ring lands beat up.... If all is clean then you can rule it out.... It's not likely but I thought I'd throw it out there.
__________________
Rich Biebel S/C 1479 Stock 147R |
|
|
|
|
08-24-2021, 02:08 PM
|
#6 |
|
VIP Member
Join Date: Nov 2001
Location: The Lowcountry.
Posts: 2,974
Likes: 2,586
Liked 2,725 Times in 961 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
Just thinking out of the box, how old is the Harmonic Balancer?
|
|
|
|
|
08-24-2021, 08:05 PM
|
#7 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,640
Likes: 1,937
Liked 10,712 Times in 2,230 Posts
|
Re: Micro Welding of bearing shell to rod housing bore
At least 6 to 8 years old. Last time it was down I had crank checked for balance it was ok
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
