sbc cylinder head flow

Mike Pearson · 08-15-2008, 09:29 AM

I dont think anyone is going to tell you what your there flow numbers are. Its a comparison of what you had to what changes you have made to the ports. Flow them stock then flow them once you have done some port work. If you are working in the right area of the port the flow numbers should be better. If you have one of the small flow benches it will not show you everything. I think most of the head guys flow them at 25 inches of vaccum. That 305 head has a large intake runner so you can get some really good flow numbers on the bench but with the small cu. in. there will not be any velocity. One of my friends ran a 305 for years and his heads were no where near the cc limit. He ran 1.00 under with those heads. Be very careful porting the 305 heads as they are very proned to cracking and water leaks.

mr305 · 08-15-2008, 12:22 PM

Thanks mike, appriciate all the help i can get. lol

Mike Pearson · 08-15-2008, 02:02 PM

MR305,

Check your private messages

Mike

Aaron Keown · 08-16-2008, 12:31 AM

Around 300 cfm for most 1.94 heads.Just remember that a flow bench can easily lead you in the wrong direction when porting heads.Hope this helps you out a little bit.

mr305 · 08-17-2008, 03:26 PM

Your exactly right Aaron I'll remember that thanks!!!!

08-15-2008, 09:29 AM	#1
Mike Pearson VIP Member Join Date: Mar 2007 Posts: 2,447 Likes: 615 Liked 1,923 Times in 578 Posts	Re: sbc cylinder head flow I dont think anyone is going to tell you what your there flow numbers are. Its a comparison of what you had to what changes you have made to the ports. Flow them stock then flow them once you have done some port work. If you are working in the right area of the port the flow numbers should be better. If you have one of the small flow benches it will not show you everything. I think most of the head guys flow them at 25 inches of vaccum. That 305 head has a large intake runner so you can get some really good flow numbers on the bench but with the small cu. in. there will not be any velocity. One of my friends ran a 305 for years and his heads were no where near the cc limit. He ran 1.00 under with those heads. Be very careful porting the 305 heads as they are very proned to cracking and water leaks. __________________ Mike Pearson 2485 SS

08-15-2008, 12:22 PM	#2
mr305 Member Join Date: May 2007 Location: Monticello Posts: 160 Likes: 0 Liked 2 Times in 1 Post	Re: sbc cylinder head flow Thanks mike, appriciate all the help i can get. lol

08-15-2008, 02:02 PM	#3
Mike Pearson VIP Member Join Date: Mar 2007 Posts: 2,447 Likes: 615 Liked 1,923 Times in 578 Posts	Re: sbc cylinder head flow MR305, Check your private messages Mike __________________ Mike Pearson 2485 SS

08-16-2008, 12:31 AM	#4
Aaron Keown Junior Member Join Date: Mar 2004 Location: 1710 Dutch Lane,Jeffersonville,IN Posts: 63 Likes: 0 Liked 0 Times in 0 Posts	Re: sbc cylinder head flow Around 300 cfm for most 1.94 heads.Just remember that a flow bench can easily lead you in the wrong direction when porting heads.Hope this helps you out a little bit.

08-17-2008, 03:26 PM	#5
mr305 Member Join Date: May 2007 Location: Monticello Posts: 160 Likes: 0 Liked 2 Times in 1 Post	Re: sbc cylinder head flow Your exactly right Aaron I'll remember that thanks!!!!