|
|
![]() |
#1 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,999
Likes: 64
Liked 772 Times in 192 Posts
|
![]()
And I don't mean taking a shower.
Where can you get a car body chemically stripped? I am really not talking about chemical milling, just cleaning the old sound deadener, paint, body filler, rust, etc, so I can work on clean sheet metal. All the places I knew that did that are no longer in business. I understand about the EPA and all that, but I don't want to do this by hand. Preferably in the South. Thanks! Dwight Southerland |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2007
Posts: 805
Likes: 0
Liked 3 Times in 1 Post
|
![]()
Dwight i know there is a place in Atlanta but then thats a way's off for you!
![]()
__________________
Woodro Josey 2002 STK |
![]() |
![]() |
![]() |
#3 |
Live Reporter
|
![]()
They are still around but you have to search 'em out -- we have one in nearby Allentown , PA.....
__________________
Jack Matyas 1547 FS/C 2015 Camaro COPO # 62- 2012 Camaro Convertible COPO |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Sep 2006
Location: Orange City Fl
Posts: 764
Likes: 0
Liked 0 Times in 0 Posts
|
![]()
Dwight
Try high pressure waterblasting. Saw a few cars done that way and looked like brand new stamping. Hammer |
![]() |
![]() |
![]() |
#5 |
VIP Member
Join Date: Jun 2006
Posts: 3,416
Likes: 522
Liked 330 Times in 178 Posts
|
![]()
See if you can find a place that does SODA blasting/washing--Saw a old Corvette that a guy did did not hurt the weatherstripping or other soft parts-- Took it right down to raw fiberglass no pits or gouging like you get from sand blasting--Comp 387
|
![]() |
![]() |
![]() |
#6 |
Member
Join Date: May 2005
Location: Chalybeate Springs, N.C.
Posts: 131
Likes: 18
Liked 29 Times in 8 Posts
|
![]() |
![]() |
![]() |
![]() |
#7 |
Member
Join Date: May 2005
Location: Covington, La
Posts: 311
Likes: 63
Liked 83 Times in 20 Posts
|
![]()
Dwight:
As I understand it, you want to remove the undercoat from under the floors, is that correct? If that is the case, over the last 30 years or so, I had the occasion to remove undercoating many times. The method I used was to heat the undercoating with a heat gun and use a scraper/Putty knife etc. It is a slow process, but it always works. If you are ever have the chance to see my car, I invite you to inspect the underside of my car. All you will see is a clean underside and a lot of red paint. If your car is completely apart, turn the body on the side. I rolled my car over and rested the roof line gutter on an old tire for support. This did not harm any part of the car and it makes it alot easier to do the job. I was too cheap to buy a rotessery. Good luck on your project. Remember, no one plans to fail, they just fail to plan! A little planning goes a long way!
__________________
John Duzac D/S 4448 STK |
![]() |
![]() |
![]() |
#8 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,999
Likes: 64
Liked 772 Times in 192 Posts
|
![]()
Thanks everybody for the info.
John - I appreciate your nuts and bolts perspective. I did find a place in Jackson, MS and a place in Ball, LA that do chemical stripping, but I cannot justify all the cost for this project. I am now gathering up materials to do a rudimentary rotisserie and plan on doing this by hand. I probably will do soda blasting after the undercoating and sound deadener are removed. I have also done a few cars in my time, but this one has an unusually thick layer of undercoating and I was just looking for a easy way out. |
![]() |
![]() |
![]() |
#9 | |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 3,043
Likes: 712
Liked 1,577 Times in 581 Posts
|
![]() Quote:
![]() ![]() ![]() ![]() |
|
![]() |
![]() |
![]() |
#10 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,999
Likes: 64
Liked 772 Times in 192 Posts
|
![]()
Wow! I thought I had an original idea!!
|
![]() |
![]() |
![]() |
|
|