|
![]() |
#21 |
Senior Member
Join Date: Oct 2003
Location: Lower Slower Delaware
Posts: 501
Likes: 14
Liked 217 Times in 78 Posts
|
![]()
My PPP shifter has been acting up on the 1-2 shift going past 2nd so disassembled it either it needed maintenance or was worn out
The original lube was full of dirt cleaned it all off everywhere Don't mess with the handle unless you have some patience. Used Super Lube silicon grease as the assembly lube Soaked the cable in trans fluid for a few days Re installed making sure alignment and adjustment are as instructed. Initially my impression was the spring that pushed the rod/disc up needed to slow down but with bench testing and in the car before and after the shift lever needed to speed up. That must be why PPP states most problems are in the cable.
__________________
Frank Ferrucci I/SA 1271 "Be Thankful for the Gifts You are Given" |
![]() |
![]() |
![]() |
#22 |
Member
Join Date: Mar 2010
Posts: 117
Likes: 35
Liked 72 Times in 39 Posts
|
![]()
Signman,
I assume you fixed your issue? |
![]() |
![]() |
![]() |
#23 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,908
Likes: 85
Liked 513 Times in 247 Posts
|
![]()
Must be a PPP shifter thing, never had an issue with the Turbo Action shifter in my Firebird no mind the OEM shifter in my Chevelle.
|
![]() |
![]() |
![]() |
#24 | |
Senior Member
Join Date: Sep 2006
Location: Fulton County, PA
Posts: 554
Likes: 10
Liked 776 Times in 218 Posts
|
![]() Quote:
OP's question said 'visibly there?s a bit of a build up of crud on the shifter mechanism. Will give it a clean, what are you guys using to relube it?' If mine had a build up of crud on it, I would clean it too. A thin film of grease, maybe a synthetic like Amsoil would be fine, but would attract dirt, requiring it to be cleaned again at some point.. A dry film lube should also be okay. Not a lot of pressure on those parts. just need to work smoothly. |
|
![]() |
![]() |
![]() |
#25 | |
Senior Member
Join Date: Sep 2006
Location: Fulton County, PA
Posts: 554
Likes: 10
Liked 776 Times in 218 Posts
|
![]() Quote:
Perhaps an upgrade is called for. Looks like a lightweight cable with standard Morse ends. Should not be hard to accomplish. |
|
![]() |
![]() |
![]() |
#26 | |
Senior Member
Join Date: Sep 2006
Location: Fulton County, PA
Posts: 554
Likes: 10
Liked 776 Times in 218 Posts
|
![]() Quote:
They are functional, built to take a beating, but nothing precision about them. |
|
![]() |
![]() |
![]() |
#27 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,908
Likes: 85
Liked 513 Times in 247 Posts
|
![]()
yea the B&M shifter in my dragster ain't been cleaned nor relubed either, that too must have been built "to work in crappy, dirty environments"
![]() Frankly, IMO, this thread is ridiculous! If a little crud on your shifter mechanism causes you to lose sleep then wipe it off and go race. Further, if you feel a relube is necessary too, chose your favorite lube, grease, oil and just dab it for christ sake. If you must be told what lube to use, IMO you don't belong behind the wheel of a race car but you could call the manufacturer and ask! |
![]() |
![]() |
Liked |
![]() |
|
|