Stock ?s

MR DERBY CITY · 10-25-2021, 12:33 PM

For what its worth, not sure there are any GOOD factory 305 blocks out there..

dartman · 10-25-2021, 01:57 PM

electric fuel pump
electric water pump
electric fan

all yes's

Larry Hill · 10-25-2021, 01:58 PM

Cool I will put spacers in an early 360 and use a 318 crank. I dont think spacers are approved for stock.

SSDiv6 · 10-25-2021, 02:05 PM

Quote:

Originally Posted by Larry Hill

Cool I will put spacers in an early 360 and use a 318 crank. I dont think spacers are approved for stock.

Section 11A, page 3 - Stock Cars

CONNECTING RODS

''...The use of rod and crank spacer bearings prohibited."

Lyn Smith · 10-25-2021, 02:45 PM

Didn't mean to open up a can of worms but aren't most bowtie blocks large journal blocks? How do they run a 3" stroke crank in them to make them a 265 or 283?. I went through tech in 2019 with my 265 made from a 305 block and the tech guys noted it had side mounts and I told them what i had done. It was ok then?

jmantle · 10-26-2021, 08:28 PM

Quote:

Originally Posted by SSDiv6

Section 11A, page 3 - Stock Cars

CONNECTING RODS

''...The use of rod and crank spacer bearings prohibited."

My understanding of that rule is you can't run smaller journals the what the intended combo came with. If you're running a 265 crank in a 305 block, journal sizes are still "stock".

Lyn Smith · 10-25-2021, 03:09 PM

Larry, go ahead and run your 318 crank with the spacer bearings. I wont tell anyone.LOL

rod · 10-25-2021, 08:42 PM

thanks guys. engine not so big a deal. its the 4 speed and rear axle that are important.
Rod in AZ

427FE · 10-26-2021, 02:09 PM

As a newbie myself, while a rule book is great, you also need specific info for your combination. Visit the classracerinfo.com site and it will give specific parts and part #'s for some things you asked about.

10-25-2021, 12:33 PM	#1
MR DERBY CITY VIP Member Join Date: Feb 2014 Location: Derby City, USA Posts: 3,638 Likes: 1,083 Liked 7,938 Times in 1,519 Posts	Re: Stock ?s For what its worth, not sure there are any GOOD factory 305 blocks out there..

10-25-2021, 01:57 PM	#2
dartman Member Join Date: Oct 2005 Location: N.S. CANADA Posts: 498 Likes: 160 Liked 68 Times in 41 Posts	Re: Stock ?s electric fuel pump electric water pump electric fan all yes's __________________ 1231 FS/D Drag Pak 1231 E/SA 71 Demon Kelly MacKay

10-25-2021, 01:58 PM	#3
Larry Hill Live Reporter Join Date: Oct 2004 Location: Hickory, Ky Posts: 10,640 Likes: 1,937 Liked 10,708 Times in 2,229 Posts	Re: Stock ?s Cool I will put spacers in an early 360 and use a 318 crank. I dont think spacers are approved for stock. __________________ IHM Used Parts https://ihmusedparts.com 888-821-1817

10-25-2021, 02:45 PM	#5
Lyn Smith VIP Member Join Date: Dec 2001 Location: Pontiac,il. Posts: 1,201 Likes: 282 Liked 972 Times in 195 Posts	Re: Stock ?s Didn't mean to open up a can of worms but aren't most bowtie blocks large journal blocks? How do they run a 3" stroke crank in them to make them a 265 or 283?. I went through tech in 2019 with my 265 made from a 305 block and the tech guys noted it had side mounts and I told them what i had done. It was ok then? Last edited by Lyn Smith; 10-25-2021 at 03:11 PM.

10-25-2021, 03:09 PM	#7
Lyn Smith VIP Member Join Date: Dec 2001 Location: Pontiac,il. Posts: 1,201 Likes: 282 Liked 972 Times in 195 Posts	Re: Stock ?s Larry, go ahead and run your 318 crank with the spacer bearings. I wont tell anyone.LOL

10-25-2021, 08:42 PM	#8
rod Member Join Date: Dec 2009 Location: Kingman, NW AZ. in the middle of the longest stretch of Route 66 Posts: 315 Likes: 0 Liked 20 Times in 15 Posts	Re: Stock ?s thanks guys. engine not so big a deal. its the 4 speed and rear axle that are important. Rod in AZ

10-26-2021, 02:09 PM	#9
427FE Member Join Date: Sep 2016 Location: Monroe Twsp, NJ Posts: 192 Likes: 260 Liked 348 Times in 79 Posts	Re: Stock ?s As a newbie myself, while a rule book is great, you also need specific info for your combination. Visit the classracerinfo.com site and it will give specific parts and part #'s for some things you asked about.