|
01-19-2019, 12:26 PM | #11 |
Senior Member
Join Date: Jul 2003
Posts: 810
Likes: 600
Liked 889 Times in 320 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Dave Layer and myself were dyno'ing one afternoon over at his shop. I don't know how we missed it, but we made a complete 7800 rpm pull after the oil pump pic-up broke off on the previous pull. Embarrassing for both of us,. I don't know what we were looking at, but obviously not what we were supposed to be. The printout let us know we only had 5 lbs. of pressure the entire pull. We pulled all the caps, and the bearings looked like they had never been ran. Pretty unbelievable. The oil was Amsoil 10-30 Racing.
__________________
Jeff Niceswanger 3740 SS |
Liked |
01-19-2019, 01:36 PM | #12 | |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 892
Likes: 65
Liked 229 Times in 107 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Quote:
|
|
01-19-2019, 03:42 PM | #13 |
VIP Member
Join Date: Dec 2001
Location: phoenix
Posts: 1,434
Likes: 55
Liked 680 Times in 269 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
|
01-19-2019, 04:23 PM | #14 |
Senior Member
Join Date: Jul 2003
Posts: 810
Likes: 600
Liked 889 Times in 320 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
I looked up the sheets. Five horsepower. The pick-up broke on pull # 3 and the no oil pressure was pull was # 4. The short block had been broke in previously with a different set of heads. So oil temp might have been a little of that five horsepower. Dave's dyno did not register oil temp. Experienced dyno operators on here will know better than me
Man we sure do miss that guy ………..
__________________
Jeff Niceswanger 3740 SS |
01-19-2019, 08:16 PM | #15 |
VIP Member
Join Date: Feb 2014
Location: Derby City, USA
Posts: 3,362
Likes: 907
Liked 6,764 Times in 1,317 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
A very well respected engine builder told me that on one occasion the customer told him to drain all the oil out of the SBC engine before the last pull, it picked up 8 HP and was still in one piece when disassembled for a freshen up......I won’t reveal his name but he was the mayor of a small city between Texas and Arkansas.....
..LOL. ,!!! |
01-19-2019, 08:41 PM | #16 |
VIP Member
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,173
Likes: 1,023
Liked 772 Times in 231 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Pull the pan when the engine is still hot/warm and you won't see that. High zinc oils (over 1,000 ppm) will precipitate additives when the oil is cold. -Al
__________________
"That'll never work....." Last edited by Alan Nyhus; 01-19-2019 at 08:55 PM. |
Liked |
01-19-2019, 08:49 PM | #17 |
Senior Member
Join Date: May 2007
Location: DRAGSTRIP
Posts: 810
Likes: 650
Liked 478 Times in 139 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
So 5-8 hp from 10w30 to no oil ! Is it really worth any hp, from 10w30 to 0w5 LOL .we all do it ,but.......
__________________
5664 AA/SA 1970 NOVA Last edited by TOSTO RACING; 01-19-2019 at 08:53 PM. |
01-19-2019, 08:57 PM | #18 |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 892
Likes: 65
Liked 229 Times in 107 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Oil helps the rings seal , without any maybe you would lose power from that and offset the gains from low oil pressure .
|
01-19-2019, 10:35 PM | #19 |
VIP Member
Join Date: Jan 2002
Location: Central Massachusetts
Posts: 1,386
Likes: 628
Liked 392 Times in 85 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Looking for Opinions / Experiences on the differences between using Valvoline VR 10w-30 Synthetic-Blend vs Valvoline VR 10w-30 "Full Synthetic" motor oil?
Specifically with respect to ring wear? |
01-20-2019, 12:03 PM | #20 | |
Member
Join Date: Feb 2009
Posts: 244
Likes: 1
Liked 8 Times in 7 Posts
|
Re: Penn vs Valvoline test results..Ed Wright
Quote:
The question that I can't seem to get a decent answer to is why so many racers use multi weight oil instead of straight weight. |
|
Liked |
|
|