Science behind building a converter

[MR DERBY CITY]

Lots of experience and a nice pair of pliers will get you a long way in the converter business. Am I correct YAK ?.......M.J.

[Ed Wright]

Have a dyno sheet handy, if you have one, when you call to order one.

[Rob Petrie E395]

Originally Posted by Ed Wright

Have a dyno sheet handy, if you have one, when you call to order one.

What do I do if I don't have that?

[west coast]

Wasn't looking for a 2 hour seminar or give anybody carpal tunnel from typing. Just basics I know there is a big difference between stock/SS, comp style stuff then the super classes and top sportsmen stuff but there seems to be some interesting stuff going on with the top sportsmen like lock up converters. Back to the subject so there is colored charts and graphs they work off as a base line then experience from there takes over. In a performance class like us getting the car to 60ft is key, specially with the weight of some of these cars. So with the dyno sheet ( and all other info like weight and gear ratio of rear end and tranny's first gear, cam, head, intake) in hands of the converter company where are they shooting too for the flash of the converter to happen at peak torque or some percentage above or below it?

[Mark Yacavone]

That's insider information, James. j/k

Actually the charts and graphs I've seen have to do with the GM 245 mm core, which is a step larger than the old Opel standby. There are about 8 different factory impellers (fin angles) plus 4 or 5 stators, so it's kind of a mix and match deal there.
Not so much with the Opel 8".
There's really only a couple of stator designs, so they have to be machined to fine tune the combination. The fin angle starts out basically straight ahead or neutral, so it has to be adjusted within it's workable window.
There are a few more subtle tuning tricks but you're always walking a fine line there.

Seeing a torque converter multiplies torque, it stands to reason you would want to multiply as much as you can. Sometimes that flash point wants to be a little over peak, at it, or a little under, but yes, right around it it.

No dyno sheet , but with a popular combo? Usually no problem, with a large enough data base.
Odd ball or Dime Rocket type combos? That's where a lot of S/SS racing experience helps, but also a s.w.a.g. sometimes.

Gotta give the carpel a rest, but specific questions?

[FireSale]

Just to fill in a bit, we're talk'in 5.0L aka 302 EFI Ford spinning a C4 in a Fox Mustang. K-L/SA. Converters should be generic on a conceptual level, which is what Jim is after here, but sometimes it helps to know the combo.

Jim: Performance Automatic has a downloadable torque converter order sheet that might give you an idea of the info needed to put one together for a given engine combo. I have their foreword shift servo and it's first rate.

Dale

[Chris Hill]

Mark,


Are there any general converter fundamental governing equations?


Folks always talk about flash rpm and lock-up, but what happens to torque multiplication when flash rpm is "adjusted"?


Also, what happens if fluid viscosity changes?

[Mark Yacavone]

Originally Posted by MR DERBY CITY

Lots of experience and a nice pair of pliers will get you a long way in the converter business. Am I correct YAK ?.......M.J.

Yes..that and a huge data base.

I was hoping I could stay out of this for now, only because it's going to take about a two hour dissertation to answer all of James's questions.
I was hoping Ultimate Lenny had some time to spend with us ;-).
Let me say this for now.
There are formulas and tables for phantom engines that can used as a guideline, but seeing most S/SS engines don't match up very well, the builder is still going by feel and experience most of the time.
Most of you have had a new ,latest trick of the week engine that won't go down the track as fast as you're old basic standby. Then you can imagine what a converter builder has to go through with that same combo.