HOME FORUM RULES CONTACT
     
   
   

Go Back   CLASS RACER FORUM > Classifieds > Race Parts: Classifieds


Reply
 
Thread Tools Search this Thread Display Modes
Old 06-11-2024, 07:07 AM   #1
JeffM
Member
 
Join Date: Feb 2007
Posts: 136
Likes: 87
Liked 3 Times in 3 Posts
Default LS/SBC parts - Wheels, Converters, misc

Weld Alumastar 15 x 12 rear wheels with 4.75 pattern and 3” BS. $800.00. Very good condition, no screw holes

Precision Performance Products Kwik shift I manual shifter – excellent condition – no mounting plates. Black. 3 speed, push to shift with clean neutral. $350.00

TCI SBC/BBC lightweight 29.2 168T flexplate PN 399870LW, like new. Weighs 6.09lbs. Can barely see the contact patch on the starter ring. Original date was 1/19, but was only ran in the car for 2 races. Will need recertified. Excellent condition $300.00

Jesel Dogbone lifters LFD-44002 .842 Diameter – set of 16 – $800.00
LS Bryant crankshaft – 4” stroke – 58x - $2800

Carillo rods 6.1 rods (was used with Bryant crankshaft above)
BE :2.2253
PE :0.9285
Length: 6.100
B Width : 0.938
$1200.00

Forged small journal 327 GM crankshaft. Offset ground (.020 under) by Shaftech. 1.979 rods, 2.300 mains – 3.263 stroke $750.00

Oliver I beam 5.7 rods set of 8 (was used with Shaftech crank above)
BE: 2.125
PE: 928
Length: 5.7
Weight each: 575 Grams
$800.00

8” ATI converter - Flashed 6500 behind 427/430 LS Combo –Powerglide spline - $500

7" Converter - Dynamic. Powerglide input, flashed 7000 behind 327/275 hp combo. - $500.00

Wilson 1” 4 hole aluminum tapered spacer – Dominator flange PN 024110 - $150 used for test only

6.00 12 bolt ring and pinion. Ring gear has been backcut - less than 10 runs $250.00

Biondo RPM2 shift controller – 2 LCD bars are inactive, but still legible to program - $100

Polished fabricated valve covers with baffles tall - $100.00


Jesel 1.8 intake/1.6 exhaust sportsman aluminum lightened rocker arms. SBC 23 degree heads. Rockers and shafts are refurbished from Jesel in sealed bags never ran. Rocker stands and bolts are used. No rocker studs and hold down bolts $700.00.

Manley 221443P-16 valve springs with 23648-16 Ti - retainers, locks and 42573-16 locators (run on dyno) $300 for set.

ATI balancer pulley PN 916794 4 groove aluminum 6.430 diameter - New $40.00
ATI balancer pulley PN 916732 4 groove aluminum 6.430 diameter – used $50.00

CV products 3/8 pushrods (qty 18) 9.200 x .080 x 5/16 ends – used but good condition – $30.00
Trend 3/8 pushrods (qty 16) 7.450 x .135 x 5/16 ends – used but good condition) $50
Trend 7/16 tapered pushrods (qty 16) 9.400 x .165 x 5/16 ends new - $150
Trend 3/8 pushrods (qty 8) 9.400 x .135 x 5/16 ends used - $25
Trend 3/8 pushrods (qty 8) 9.450 x .135 x 5/16 ends used - $25
Trend (qty 17) – 9.150 DBL taper .135 wall pushrods 5/16 ends (used good) $35
Trend 9.400 DBL taper .135 wall pushrods 5/16 ends (11) new $150
Trend 9.300 DBL taper .135 wall pushrods 5/16 ends (11) new $150

JRI 2010-2015 Camaro front struts $500.00 used.

1 – Lingenfelter billet steel LS block girdle, No hardware $500
2 GM truck oil pans (1999-2006) pan only $50.00 each

Pit Pal Pit Ramps 280 with vertical storage pouch for trailer
Aluminum, 24.00 in. Length, 8.00 in. Width, 2.75 in. Height, Pair with pouch $200

Can bring to Norwalk National event

260-223-0157
superstock@live.com
__________________
Jeff Myers
SS3254
S1522

Last edited by JeffM; 06-13-2024 at 06:04 AM.
JeffM is offline   Reply With Quote
Old 06-13-2024, 07:54 AM   #2
BZenzen
Junior Member
 
BZenzen's Avatar
 
Join Date: Sep 2012
Location: Deployed
Posts: 87
Likes: 26
Liked 241 Times in 39 Posts
Default Re: LS/SBC parts - Wheels, Converters, misc

Hi Jeff, is the shifter for a TH 350? FWD or Reverse valve body? Thanks!
__________________
Brian Zenzen
SS 5404
STK 5401
BZenzen is online now   Reply With Quote
Old 06-13-2024, 08:00 AM   #3
JeffM
Member
 
Join Date: Feb 2007
Posts: 136
Likes: 87
Liked 3 Times in 3 Posts
Default Re: LS/SBC parts - Wheels, Converters, misc

Quote:
Originally Posted by BZenzen View Post
Hi Jeff, is the shifter for a TH 350? FWD or Reverse valve body? Thanks!

Any 3 speed transmission with clean neutral all the way forward. Push to shift. Park is all the way in the rear P, R,1,2,3,N. Cable exits in the rear.
__________________
Jeff Myers
SS3254
S1522
JeffM is offline   Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 03:09 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.