I'm going to build a smooth idle 427 and drag test it - Page 3

Stan Weiss · 02-05-2021, 12:53 AM

Took something I had made a few changes and did a rough simulation.

DA = 0

60 Foot ET = 1.5076
330 Foot ET = 4.4113
1/8 Mile ET = 6.9378
1/8 Mile MPH = 96.7141
1000 Foot ET = 9.1421
1/4 Mile ET = 11.0173
1/4 Mile MPH = 120.2224

Stan

Frank Castros · 02-05-2021, 08:04 AM

My guess is 500hp based on the very high quality of the build.

HP HUNTER · 02-05-2021, 10:58 AM

The first test is some what typical, and the second test was my best. From what I can see from the average power, that should get me there, 4200-6100 RPM (11.00) should be easy.

stage1scott · 02-05-2021, 01:05 PM

Quote:

Originally Posted by HP HUNTER

The first test is some what typical, and the second test was my best. From what I can see from the average power, that should get me there, 4200-6100 RPM (11.00) should be easy.

very nice!!

MAURICE BLENDHEIM · 02-06-2021, 12:28 PM

Quote:

Originally Posted by HP HUNTER

The first test is some what typical, and the second test was my best. From what I can see from the average power, that should get me there, 4200-6100 RPM (11.00) should be easy.

HP... I'm just wondering if you made any pulls starting at a lower RPM ? It would be interesting to see what the TORQUE numbers would be from say 2500-3500rpm. Very Good results from this project. MB

HP HUNTER · 02-06-2021, 07:42 PM

Quote:

Originally Posted by MAURICE BLENDHEIM

HP... I'm just wondering if you made any pulls starting at a lower RPM ? It would be interesting to see what the TORQUE numbers would be from say 2500-3500rpm. Very Good results from this project. MB

Thanks, I didn't pull it lower than 3500, I knew I'd never see that on the track, I doubt there was more TQ below 3500. I can tell you from driving the car off idle TQ is very good, but as you know theres always a trade off-and I'm sure it going to be on the top. But it sure runs good, just wonder what it could have made if I really got after it, intake work, oil pan work, lightened the bottom end up, 1.8 intake rocker, more compression. Vacuum was 15 inches @ 750 RPM @ 6400 feet altitude. Heres a video.

Glenn Briglio · 02-07-2021, 10:16 AM

Quote:

Originally Posted by HP HUNTER

Thanks, I didn't pull it lower than 3500, I knew I'd never see that on the track, I doubt there was more TQ below 3500. I can tell you from driving the car off idle TQ is very good, but as you know theres always a trade off-and I'm sure it going to be on the top. But it sure runs good, just wonder what it could have made if I really got after it, intake work, oil pan work, lightened the bottom end up, 1.8 intake rocker, more compression. Vacuum was 15 inches @ 750 RPM @ 6400 feet altitude. Heres a video.

There is more torque at lower rpm. Look where the tq is at 3500 rpm. Your correct and probably never see it at the track.

Painter · 02-07-2021, 03:23 PM

Who did the carbs?

HP HUNTER · 02-07-2021, 08:23 PM

1. Harold Bettes Dissident
2. Vintage Muscle Car

gmonde · 02-07-2021, 09:21 PM

whats the weight on the car w/driver?

02-05-2021, 12:53 AM	#21
Stan Weiss Senior Member Join Date: Apr 2020 Location: Phila, PA Posts: 606 Likes: 0 Liked 545 Times in 291 Posts	Re: I'm going to build a smooth idle 427 and drag test it Took something I had made a few changes and did a rough simulation. DA = 0 60 Foot ET = 1.5076 330 Foot ET = 4.4113 1/8 Mile ET = 6.9378 1/8 Mile MPH = 96.7141 1000 Foot ET = 9.1421 1/4 Mile ET = 11.0173 1/4 Mile MPH = 120.2224 Stan Attached Thumbnails

02-05-2021, 08:04 AM	#22
Frank Castros VIP Member Join Date: Nov 2001 Location: The Lowcountry. Posts: 2,638 Likes: 2,151 Liked 2,073 Times in 766 Posts	Re: I'm going to build a smooth idle 427 and drag test it My guess is 500hp based on the very high quality of the build.

02-05-2021, 10:58 AM	#23
HP HUNTER Senior Member Join Date: Feb 2012 Location: Colorado Springs Colorado/Thousand Oaks Ca Posts: 606 Likes: 68 Liked 238 Times in 97 Posts	Re: I'm going to build a smooth idle 427 and drag test it The first test is some what typical, and the second test was my best. From what I can see from the average power, that should get me there, 4200-6100 RPM (11.00) should be easy. Attached Thumbnails Last edited by HP HUNTER; 02-05-2021 at 11:04 AM.

02-07-2021, 03:23 PM	#28
Painter Member Join Date: Dec 2012 Posts: 227 Likes: 4 Liked 161 Times in 45 Posts	Re: I'm going to build a smooth idle 427 and drag test it Who did the carbs?

02-07-2021, 08:23 PM	#29
HP HUNTER Senior Member Join Date: Feb 2012 Location: Colorado Springs Colorado/Thousand Oaks Ca Posts: 606 Likes: 68 Liked 238 Times in 97 Posts	Re: I'm going to build a smooth idle 427 and drag test it 1. Harold Bettes Dissident 2. Vintage Muscle Car

02-07-2021, 09:21 PM	#30
gmonde Senior Member Join Date: Nov 2007 Posts: 615 Likes: 56 Liked 166 Times in 59 Posts	Re: I'm going to build a smooth idle 427 and drag test it whats the weight on the car w/driver?