|
11-10-2015, 02:16 PM | #11 |
VIP Member
Join Date: Oct 2008
Location: Somerset,Ky
Posts: 1,305
Likes: 201
Liked 118 Times in 50 Posts
|
Re: Boss Mustang stocker
looking good,Bill
Mike Taylor 3601 |
11-10-2015, 05:38 PM | #12 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
The rest of the sheetmetal parts are down here....
__________________
__________________ Bill Diehl B200 C/D STK |
11-10-2015, 05:41 PM | #13 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
I was going to rebuild the factory headlight assemblies..but being 45 years old and they looked like they were 145 years old, I got these instead.
These things are really nice even if they are offshore clones
__________________
__________________ Bill Diehl B200 C/D STK |
11-10-2015, 05:43 PM | #14 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
and they will bolt on to this....
__________________
__________________ Bill Diehl B200 C/D STK |
11-10-2015, 06:04 PM | #15 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
If it wasn't a cleveland I wouldn't be using these, but it does make for a nice way to restrict the oil, should have posted them a few pics back with the rest of the cam gear
__________________
__________________ Bill Diehl B200 C/D STK |
11-11-2015, 01:15 PM | #16 |
VIP Member
Join Date: Feb 2014
Location: Lakewood Washington
Posts: 1,407
Likes: 29
Liked 237 Times in 127 Posts
|
Re: Boss Mustang stocker
Looks nice. What's your source for sheet metal? I used mostly Dynacorn stuff from CJPony Parts to rebuild my 68 coupe. Floor pans, radiator support, a fender and such. Pretty descent stuff for Korean stamping.
I don't have access to a rule book on this computer but I think you are allowed to cut that cross member for header clearance. Dale
__________________
Dale Shearon 68 Mustang 6394 |
11-11-2015, 01:36 PM | #17 | |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
Quote:
I am tig welding all the panels back in also, but its a slow process in between bending tubing for the roll cage and pouring concrete for a living Headers where designed for the engine to sit lower.....but rules state I cant do that, raise the engine to stock location they hit the floor, lower the engine hits the crossmember..no problem, I have a plan wish I could use a dif intake manifold though, I have the best set of heads on the planet (nobody has anything close) with the worst manifold bolted to them
__________________
__________________ Bill Diehl B200 C/D STK Last edited by Bill Diehl; 11-11-2015 at 01:46 PM. |
|
11-12-2015, 04:31 AM | #18 | |
Senior Member
Join Date: Nov 2007
Location: Div. 6, Eastern, WA
Posts: 699
Likes: 2,445
Liked 224 Times in 106 Posts
|
Re: Boss Mustang stocker
Quote:
Can those cam beearings be used with an iron cam ? Comp told me 400lbs open was about it for an iron cam but those 1427's are 500 @ .600" so a tick less with the Boss cam.
__________________
Dave Noll, E/FS ,?/SA 6526 |
|
11-12-2015, 08:47 AM | #19 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
You will just have to believe me
__________________
__________________ Bill Diehl B200 C/D STK |
11-12-2015, 09:01 AM | #20 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Boss Mustang stocker
The exhaust crossover, lead is too much of a hassle, tin leaks....aluminum plate works much better and don't have to worry about anything falling out or finding its way into the exhaust bowl. and I am able to swap manifolds without screwing around with it.
__________________
__________________ Bill Diehl B200 C/D STK Last edited by Bill Diehl; 11-12-2015 at 09:04 AM. |
|
|