|
06-08-2024, 10:36 AM | #51 |
Member
Join Date: Aug 2010
Location: CT
Posts: 429
Likes: 1,411
Liked 322 Times in 137 Posts
|
Re: OK, Stocker "valve jobs".
No, ONE degree is all that's allowed. Wait until you try to get the rocker to comply .
__________________
Phil Molski PMR Performance S/C 1623 |
Liked |
06-09-2024, 08:03 AM | #52 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,462
Likes: 1,752
Liked 10,091 Times in 2,095 Posts
|
Re: OK, Stocker "valve jobs".
If you installed the larger screw in studs to help stop some of the lift loss from deflection, a racer could regain the correct rocker valve angel relationship. I think
|
Liked |
06-09-2024, 02:26 PM | #53 |
Member
Join Date: Aug 2010
Location: CT
Posts: 429
Likes: 1,411
Liked 322 Times in 137 Posts
|
Re: OK, Stocker "valve jobs".
Not if you're trying to "cant" the valve - then the stud would have to also have the corresponding "cant". Think big block Chevy, the valves are angled AND canted.
__________________
Phil Molski PMR Performance S/C 1623 |
Liked |
06-09-2024, 05:36 PM | #54 |
Junior Member
Join Date: Aug 2022
Location: PHXarea. +Ohio
Posts: 57
Likes: 10
Liked 36 Times in 16 Posts
|
Re: OK, Stocker "valve jobs".
This is a great post Billy. But i think most racers have no clue what we are talking about. Going to reply ,so not directed at anyone.
__________________
Rocketmancoatings |
06-09-2024, 07:03 PM | #55 |
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 769
Likes: 860
Liked 210 Times in 82 Posts
|
Re: OK, Stocker "valve jobs".
This started because i didn’t have a clue, either! Lol!
__________________
Jim Miller 103 U/SA Last edited by goinbroke2; 06-09-2024 at 07:06 PM. |
06-09-2024, 07:09 PM | #56 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,462
Likes: 1,752
Liked 10,091 Times in 2,095 Posts
|
Re: OK, Stocker "valve jobs".
Well aware of BBC angel a cant of the valves. Spent a ton of money on a 68 427/ 400 project with 290 small plug heads. The car we got was from Wayne Shaw was a 69 350/ 350 car. I sold to John Livingston and he made the Tennessee Thunder car. NHRA made him change doors and put the key on the dash.
We enlarged the hole with an end mill to keep the tap drill from following the path of least resistance. And then spot faced the seat of the screw in stud. |
Liked |
06-10-2024, 01:50 PM | #57 |
Member
Join Date: Jun 2007
Posts: 393
Likes: 659
Liked 461 Times in 106 Posts
|
Re: OK, Stocker "valve jobs".
[QUOTE=Larry Hill;698408] ...NHRA made him change doors and put the key on the dash....
/QUOTE] Flash of nostalgia for when rules mattered and a car had to be correct for the year. Little things like a pushbutton door latch and location of the ignition switch were no doubt a total pita but before "close enough" grey areas. No, can't think of a single performance advantage but somehow I liked it better that way. |
Liked |
06-12-2024, 10:17 AM | #58 |
VIP Member
Join Date: Jun 2007
Location: from Vancouver BC Canada, now in Nova Scotia
Posts: 1,266
Likes: 250
Liked 966 Times in 268 Posts
|
Re: OK, Stocker "valve jobs".
Certainly must have been far fewer first gen 350 and B B powered, as well as automatic transmission equipped "Z/28" Camaros running in Stock and Super Stock back in the "old days". I still remember when a buddy took his 69 Camaro 427/425 Super Stocker down to Pomona, and the tech guy made him remove the SS emblem between the tail lights, since that was a COPO combination. Or when if you wanted to run a 69 Mustang 428 CJ car as a GT rather than a Mach 1, you needed to use the GT only gas cap. Things have certainly changed!
__________________
NHRA 6390 STK M/S 85 Mustang |
Liked |
|
|