|
|
02-17-2014, 01:01 AM
|
#1 |
|
Member
Join Date: Dec 2004
Location: wake forest , n.c.
Posts: 162
Likes: 2
Liked 0 Times in 0 Posts
|
Ford clevland size mains
Needing info on a 10 over front to back thurst bearing. too much crank end play. std bearing size. acl had what was needed but r out of business. king bearing only does 302 main size. not the 2.749 main size n this 9.5 windsor clevland main size block, will FE thurst bearings fit? thanks mark young.919-427-2747
__________________
nitro joes TOP GUN 3 years straight mark young |
|
|
|
02-20-2014, 04:07 PM
|
#2 |
|
Member
Join Date: Dec 2004
Location: wake forest , n.c.
Posts: 162
Likes: 2
Liked 0 Times in 0 Posts
|
Re: Ford clevland size mains
come on guys . is all of clevland snowed n?
__________________
nitro joes TOP GUN 3 years straight mark young |
|
|
|
|
02-20-2014, 04:10 PM
|
#3 |
|
Senior Member
Join Date: Jul 2004
Location: Minneapolis
Posts: 786
Likes: 2,876
Liked 370 Times in 101 Posts
|
Re: Ford clevland size mains
maybe call Jim Evanuik, 412-829-1988
__________________
Jerry Heath I/S '93 Cobra FS/J 2010 Mustang "Ebay CJ" |
|
|
|
|
02-21-2014, 09:44 AM
|
#4 |
|
VIP Member
Join Date: Oct 2008
Location: Somerset,Ky
Posts: 1,372
Likes: 357
Liked 308 Times in 103 Posts
|
Re: Ford clevland size mains
FE & C thrust bearing specs are almost identical, FE housing bore (main od size in block) FE spec is .0005 smaller than C could put FE thrust bearing in C would have slightly less crush on bearing and would probaly have .0005-.001 more clearance.
Should be able to rebuild thrust without doing anything else to crank. If in rush maybe able to cheat it ,could possibly set cap towards front or back to offset thrust bearings to get by a race or two. Mike Taylor 3601 |
|
|
|
|
02-21-2014, 10:30 AM
|
#5 |
|
Member
Join Date: Jul 2008
Location: moreno valley Ca
Posts: 266
Likes: 2
Liked 20 Times in 9 Posts
|
Re: Ford clevland size mains
Is it possible to have the crank and bearing coated to reduce the clearance.something that I had thought about, are would the coating just rub off.
__________________
7015 E/SA Sooner Storm |
|
|
|
|
02-21-2014, 11:36 AM
|
#6 |
|
Member
Join Date: Nov 2001
Location: Sweden
Posts: 103
Likes: 0
Liked 0 Times in 0 Posts
|
Re: Ford clevland size mains
Mark,
what is the clearance now? Front to back? |
|
|
|
|
02-23-2014, 12:45 PM
|
#7 |
|
Member
Join Date: Dec 2004
Location: wake forest , n.c.
Posts: 162
Likes: 2
Liked 0 Times in 0 Posts
|
Re: Ford clevland size mains
16 and nothing was galled. just shiny crank. mite just ride it till it causes a problem then weld it up if no oversize end play bearings r made for it.
__________________
nitro joes TOP GUN 3 years straight mark young |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
