Dana 60 ring and pinion

littlemanjoe · 04-27-2023, 11:16 AM

Need some advice.

I'm installing a used ring and pinion in a Dana 60.

I've had this thing all over and cannot get the ideal pattern.

They do not make this ratio anymore which is why I'm using a used one.

The Dana goes in a 3600lb footbrake Super Stock car.

dragracerray · 04-27-2023, 11:23 AM

Joe,
I learned a trick that makes things so much easier. Hone the Carrier bearings so they slip on my hand (ie are not pressed on). Don't get carried away you don't want the bearing sloppy on the Carrier. My engine guy did the honing.
If you are pressing the bearings on you may not be pinching the shims tight. Ray

littlemanjoe · 04-27-2023, 11:29 AM

Quote:

Originally Posted by dragracerray

Joe,
I learned a trick that makes things so much easier. Hone the Carrier bearings so they slip on my hand (ie are not pressed on). Don't get carried away you don't want the bearing sloppy on the Carrier. My engine guy did the honing.
If you are pressing the bearings on you may not be pinching the shims tight. Ray

That's done. I just realized the attachment didn't go. It's there now.

Mike

Steve Grady · 04-27-2023, 12:00 PM

Set it up by the Pinion Depth markings on the gear, Proper pinion bearing preload, And backlash marked on the gear.

Mike Pearson · 04-27-2023, 01:00 PM

I am not seeing any pattern on the ring gear. Put some pressure against the ring gear when checking the pattern. Looks like it might be a mismatched gear set.

littlemanjoe · 04-27-2023, 01:32 PM

Quote:

Originally Posted by Mike Pearson

I am not seeing any pattern on the ring gear. Put some pressure against the ring gear when checking the pattern. Looks like it might be a mismatched gear set.

They are a matched set. Just used and I'm not sure how they were installed before.

Jim Cimarolli · 04-27-2023, 01:42 PM

Looks to me like you don't have enough pinion shim. Have you tried quiet a bit more than what you currently have? I would try at least .015 more and see what it looks like.

littlemanjoe · 04-28-2023, 08:35 AM

Got it figured out. Thank you

Jim Cimarolli · 04-28-2023, 01:51 PM

what did you do?

Chevy55 · 04-28-2023, 05:03 PM

Use this thickness chart if you do not have access to the old shim or the old gear was not set up correctly.
I also use this chart to start over when I'm having trouble getting a pattern.

GM .035

FORD 8"-9" *020

FORD 8.8"-7.5" .030

ALL DANA'S .035

8 3/4 X 1 3/4 PIN .090

8 3/4 X 1 7/8 PIN .020

MOPAR 9 1/4 .020

04-27-2023, 11:16 AM	#1
littlemanjoe Member Join Date: Feb 2018 Location: West Layfayette Posts: 125 Likes: 195 Liked 75 Times in 28 Posts	Dana 60 ring and pinion Need some advice. I'm installing a used ring and pinion in a Dana 60. I've had this thing all over and cannot get the ideal pattern. They do not make this ratio anymore which is why I'm using a used one. The Dana goes in a 3600lb footbrake Super Stock car. Last edited by littlemanjoe; 08-08-2024 at 10:51 PM.

04-27-2023, 11:23 AM	#2
dragracerray Member Join Date: May 2017 Location: Webster, New York Posts: 217 Likes: 467 Liked 207 Times in 88 Posts	Re: Dana 60 ring and pinion Joe, I learned a trick that makes things so much easier. Hone the Carrier bearings so they slip on my hand (ie are not pressed on). Don't get carried away you don't want the bearing sloppy on the Carrier. My engine guy did the honing. If you are pressing the bearings on you may not be pinching the shims tight. Ray __________________ Ray Bassett I/SA 1687, SS/DA 1687 "SuperPro is both", unknown

04-27-2023, 12:00 PM	#4
Steve Grady Junior Member Join Date: Apr 2023 Location: Columbus, OH Posts: 73 Likes: 100 Liked 101 Times in 40 Posts	Re: Dana 60 ring and pinion Set it up by the Pinion Depth markings on the gear, Proper pinion bearing preload, And backlash marked on the gear.

04-27-2023, 01:00 PM	#5
Mike Pearson VIP Member Join Date: Mar 2007 Posts: 2,444 Likes: 613 Liked 1,916 Times in 574 Posts	Re: Dana 60 ring and pinion I am not seeing any pattern on the ring gear. Put some pressure against the ring gear when checking the pattern. Looks like it might be a mismatched gear set. __________________ Mike Pearson 2485 SS

04-27-2023, 01:42 PM	#7
Jim Cimarolli Senior Member Join Date: Mar 2002 Location: Sulphur Springs Texas Posts: 743 Likes: 146 Liked 166 Times in 46 Posts	Re: Dana 60 ring and pinion Looks to me like you don't have enough pinion shim. Have you tried quiet a bit more than what you currently have? I would try at least .015 more and see what it looks like.

04-28-2023, 08:35 AM	#8
littlemanjoe Member Join Date: Feb 2018 Location: West Layfayette Posts: 125 Likes: 195 Liked 75 Times in 28 Posts	Re: Dana 60 ring and pinion Got it figured out. Thank you

04-28-2023, 01:51 PM	#9
Jim Cimarolli Senior Member Join Date: Mar 2002 Location: Sulphur Springs Texas Posts: 743 Likes: 146 Liked 166 Times in 46 Posts	Re: Dana 60 ring and pinion what did you do?

04-28-2023, 05:03 PM	#10
Chevy55 Banned Join Date: Nov 2014 Posts: 324 Likes: 625 Liked 179 Times in 89 Posts	Re: Dana 60 ring and pinion Use this thickness chart if you do not have access to the old shim or the old gear was not set up correctly. I also use this chart to start over when I'm having trouble getting a pattern. GM .035 FORD 8"-9" *020 FORD 8.8"-7.5" .030 ALL DANA'S .035 8 3/4 X 1 3/4 PIN .090 8 3/4 X 1 7/8 PIN .020 MOPAR 9 1/4 .020

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode