Billet Aluminum Dash Bezel

pro70z28 · 04-23-2008, 10:44 PM

Thanks Keith

CPOlesen · 04-24-2008, 08:08 AM

That is a super job. I wish I had that talent. If I can't make it with Duct tape and J B Weld then I'mn toast.

pro70z28 · 04-25-2008, 10:14 PM

Thanks CPOlesen

pro70z28 · 05-04-2008, 11:17 PM

Got the bearing housing for the steering column (firewall) done this weekend. Now all I need are those back ordered steering column parts.

I got one last thing done this weekend. I pulled the old dash out & used the glove box as a plug to make this mold. Got a couple little places to touch up and then I can make up a couple fiberglass glove boxes to finish off around the intercooler. The door has that imitation leather pattern, & the Camaro logo. They came out O.K. so far.

pro70z28 · 05-05-2008, 09:56 PM

Little steering column mock-up tonight. The Mark Williams quick release hub came today.

pro70z28 · 05-22-2008, 12:00 AM

Got the brake pedal ready to go in. Rule book says it has to be covered with a non-slip surface so I cut the center out .018" and inserted a pc. of mud flap from Big "R" Hey, it works.

:wink:

pro70z28 · 05-23-2008, 04:34 PM

At first I wasn't going to post a pic of the clevis for the B-R-A-K-E pedal. But..... I'm workin' on a billboard for a spa today and ....well......I just couldn't resist the irony. HEHEHEHE

04-23-2008, 10:44 PM	#1
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel Thanks Keith

04-24-2008, 08:08 AM	#2
CPOlesen Junior Member Join Date: Dec 2007 Location: Chandler, Oklahoma Posts: 23 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel That is a super job. I wish I had that talent. If I can't make it with Duct tape and J B Weld then I'mn toast.

04-25-2008, 10:14 PM	#3
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel Thanks CPOlesen

05-04-2008, 11:17 PM	#4
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel Got the bearing housing for the steering column (firewall) done this weekend. Now all I need are those back ordered steering column parts. I got one last thing done this weekend. I pulled the old dash out & used the glove box as a plug to make this mold. Got a couple little places to touch up and then I can make up a couple fiberglass glove boxes to finish off around the intercooler. The door has that imitation leather pattern, & the Camaro logo. They came out O.K. so far.

05-05-2008, 09:56 PM	#5
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel Little steering column mock-up tonight. The Mark Williams quick release hub came today.

05-22-2008, 12:00 AM	#6
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel Got the brake pedal ready to go in. Rule book says it has to be covered with a non-slip surface so I cut the center out .018" and inserted a pc. of mud flap from Big "R" Hey, it works. :wink:

05-23-2008, 04:34 PM	#7
pro70z28 Junior Member Join Date: Mar 2008 Posts: 73 Likes: 0 Liked 0 Times in 0 Posts	Re: Billet Aluminum Dash Bezel At first I wasn't going to post a pic of the clevis for the B-R-A-K-E pedal. But..... I'm workin' on a billboard for a spa today and ....well......I just couldn't resist the irony. HEHEHEHE

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode