|
01-31-2022, 10:35 PM | #61 | |
Senior Member
Join Date: Dec 2001
Location: Elysburg, Pa
Posts: 696
Likes: 284
Liked 242 Times in 94 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
Quote:
|
|
Liked |
01-31-2022, 11:29 PM | #62 | |
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,428
Likes: 2,607
Liked 4,489 Times in 1,705 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
Quote:
__________________
We are lucky we don't get as much Government as we pay for..... Will Rogers |
|
02-01-2022, 11:47 AM | #63 |
Member
Join Date: Dec 2014
Location: Perry, GA
Posts: 329
Likes: 11
Liked 238 Times in 89 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
Mark, that's what most all my heads have looked like till these 416 heads. They seem to have a deeper turn that didn't get touched
|
02-01-2022, 01:23 PM | #64 | |
Senior Member
Join Date: Apr 2020
Location: Phila, PA
Posts: 609
Likes: 0
Liked 545 Times in 291 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
Quote:
Mark, Thanks for the picture. It has been a while since I saw this head. But from what I can remember there was an area where the bottom cut went at least twice that amount below the seat. Stan |
|
02-01-2022, 02:11 PM | #65 |
Member
Join Date: Feb 2018
Location: Jersey
Posts: 181
Likes: 171
Liked 752 Times in 146 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
I recently had the head off of the 6 cylinder on the flow bench. Boy were we surprised how good the head flowed even at the .388 lift I am allowed. Flowed better on the intake than a stock small block head, and the exhaust flowed 80% of what the intake did. The reason it flowed as good as it did was the fact that the intake ports(there are only 3 btw) are WAY too big. While I do believe flow is very important, when the rest of the engine (in this case the 200 cfm carb and small cam) can't support the flow you can get out of the head, you're going to run into an issue with air not moving fast enough. There's a reason the most common aftermarket chevy 6 cylinder head mod is to weld in a "lump" to the bottom of the intake port to take up some volume. As odd as a chevy 6 cylinder may be, I can only imagine the same principal applies to a wide range of combos.
__________________
1189 F/SA Defunzalo Racing Enterprises |
02-07-2022, 01:13 PM | #66 | |
Member
Join Date: Oct 2020
Posts: 245
Likes: 3,330
Liked 471 Times in 160 Posts
|
Re: Cylinder head flow - What is crucial in a stocker?
Quote:
Back when all we had was stock castings from which ever car Mfg. that we chose to play with, was when the "advent" of commercial Flow Bench's came to be. The use of these machines has lead us to where we are today with all the aftermarket support, and the advertised Flow Numbers helped sell products. Now in todays world of Big Horsepower and Big Engines the cylinder heads that have been developed all started off life on someone's Flow Bench. Okay that being said - we as Stocker Racers should still be able to gather useful information from these Flow Bench's, especially given the Lifts that we have to deal with. They may not be the Final answer, but I consider there use an asset in the further development of engine performance. It's a tool just like a dyno so how you use the tools that are available to us will determine the amount of improvement you'll find in your engine development programs. The facts are right in front of you, follow them as you see fit. Just my Two cents from a very small spot in a very large world. Respectfully, Henry Kunz 1534 H/SA |
|
Liked |
Thread Tools | |
Display Modes | |
|
|