|
|
![]() |
#1 |
Senior Member
Join Date: May 2020
Posts: 511
Likes: 542
Liked 494 Times in 241 Posts
|
![]()
Theoretically yes... enough to notice?... I doubt it.
How much can you take off a balancer?... a lb maybe? It's not like taking 10 lbs off of a flywheel. Just an opinion, others may know more. |
![]() |
![]() |
Liked |
![]() |
#2 |
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 390 Times in 170 Posts
|
![]()
The above, and the smaller diameter of a dampener, versus a flywheel, the effect on inertia won’t be big.
__________________
Ed Wright 4156 SS/JA |
![]() |
![]() |
Liked |
![]() |
#3 |
Senior Member
Join Date: Apr 2020
Location: Phila, PA
Posts: 793
Likes: 0
Liked 733 Times in 384 Posts
|
![]()
Exactly. Plus it also depended on how fast the rate of acceleration of the engine is. A 1 lb weight on the outside of a 6" diameter accelerating at 2000 RPM per second at 7000 RPM is taking less than 0.54 HP. Where as that 1 lb on the outside of a 12" diameter accelerating at 2000 RPM per second at 7000 RPM is taking 2.17 HP.
Stan |
![]() |
![]() |
Liked |
![]() |
#4 |
Member
Join Date: Aug 2007
Posts: 234
Likes: 484
Liked 556 Times in 69 Posts
|
![]()
I put it in the category of things that dont show a measurable increase but when added to 50 other things like that, all of a sudden your a little faster. Lol
Last edited by Cotten; 08-01-2020 at 08:54 AM. |
![]() |
![]() |
![]() |
#5 |
Junior Member
Join Date: Jan 2012
Posts: 30
Likes: 0
Liked 1 Time in 1 Post
|
![]()
Thanks you for your insightful replies to my question.
Bernhard |
![]() |
![]() |
![]() |
#6 |
Member
Join Date: Oct 2004
Location: Canada
Posts: 313
Likes: 0
Liked 6 Times in 2 Posts
|
![]()
I'll add a couple things with no verifiable info to suggest I'm correct however.. Almost all balancers are neutral or zero balanced so a change won't affect anything internal. Smaller/lighter should spin up faster but as mentioned, you'll never notice it. What is important is the name "Harmonic". A small lightweight balancer can't control internal harmonics like a heavy "factory" one does. Bearing or crank failure can be the result. Some engines and balancer brands are notorious for this.
Hopefully, a real expert chimes in here but i can guarantee you'll se nothing performance wise. Kinda similar to Roller Rockers that are magically going to add HP> JMO
__________________
Dale Posnick |
![]() |
![]() |
Liked |
![]() |
#7 | |
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,730
Likes: 2,790
Liked 2,469 Times in 695 Posts
|
![]() Quote:
added to 50 other things like that, all of a sudden you're a whole lot poorer. Lol AND THEN = Your crank is in two pieces!
__________________
John Irving 741 Stock 741 Super Stock Last edited by GTX JOHN; 08-03-2020 at 01:31 AM. |
|
![]() |
![]() |
Liked |
![]() |
#8 | |
Senior Member
Join Date: May 2020
Posts: 511
Likes: 542
Liked 494 Times in 241 Posts
|
![]() Quote:
Ended up with stock in Federal Mogul and had lots of two piece door stops! |
|
![]() |
![]() |
![]() |
#9 |
Junior Member
Join Date: Nov 2013
Posts: 89
Likes: 36
Liked 33 Times in 20 Posts
|
![]() |
![]() |
![]() |
Liked |
![]() |
#10 |
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,730
Likes: 2,790
Liked 2,469 Times in 695 Posts
|
![]()
I read it again......I laughed for a minute!
It is not easy to even smile the last few months we have suffered through.
__________________
John Irving 741 Stock 741 Super Stock |
![]() |
![]() |
Liked |
![]() |
Thread Tools | |
Display Modes | |
|
|