1967 camaro A/S project - Page 7

qtrmile2 · 02-28-2015, 08:54 PM

More progress pics from today.

Tim and Garrett working on the brake lines

qtrmile2 · 02-28-2015, 09:22 PM

Today progress Part 2

HandOverFist · 02-28-2015, 09:32 PM

Where did you get that carbon fiber roll bar padding?

Seriously, car looks fantastic!

TOSTO RACING · 02-28-2015, 09:44 PM

Jerry Bickel race cars here in town sells it! It's cool stuff !

Got some more done today got it rolling, my new lugnuts came in ,rear end all buttoned up, all front brake lines are on, steering wheel on , and all interior back in and done now , motor mounts in, and last but not least my new rear wheels lol just kidding, but I was thinking about seeing how these hook lol!!

Danny Ashley · 03-01-2015, 10:54 AM

I like the look of the carbon fiber roll bar protector bit I'm not sure if it meets the rule book specifications for padding. It reads: Adequate padding must have minimum1/4-inch compression or meet SFI Spec 45.1. I don't see how carbon fiber can be used as a padding as it doesn't compress. The Bickle site doesn't say this protector meets the SFI spec. I can see using it on the side bar to protect from scratches, but not in the head area as it offers no protection. Do you plan to use a different padding for the head area? Am I missing something here?

qtrmile2 · 03-01-2015, 11:03 AM

Quote:

Originally Posted by Danny Ashley

I like the look of the carbon fiber roll bar protector bit I'm not sure if it meets the rule book specifications for padding. It reads: Adequate padding must have minimum1/4-inch compression or meet SFI Spec 45.1. I don't see how carbon fiber can be used as a padding as it doesn't compress. The Bickle site doesn't say this protector meets the SFI spec. I can see using it on the side bar to protect from scratches, but not in the head area as it offers no protection. Am I missing something here?

Danny, You only need padding on the roll bar if your helmet is 6 inches from contacting the roll bar only.We have 45.1 in that area of contact. Type of padding depends on ET. The carbon fiber used is not 6 inches from helmet. Hope this helps. It is in the rule book too.

Danny Ashley · 03-01-2015, 12:08 PM

Thanks Tim. After looking closer I see your 45.1 in the head area. Good luck this season and I'm enjoying following your build. Regards, Danny

impstocker · 03-01-2015, 01:10 PM

Nice Build. Question, are you using stock rubber bushings in your front upper control arms?
I have solid bushings in my Impala, used solids in bottom too. Am I too "old school"

Will Lamprecht 1965 Impala I/SA in progress.

TOSTO RACING · 03-01-2015, 06:49 PM

Quote:

Originally Posted by Danny Ashley

Thanks Tim. After looking closer I see your 45.1 in the head area. Good luck this season and I'm enjoying following your build. Regards, Danny

Hey Danny that's actually my dad Vince. The carbon fiber is just for looks and to help with scratches usually guys just do a little piece , but I went ahead and did the whole bar and thought it looked good .

Thanks Tim

HandOverFist · 03-01-2015, 06:52 PM

Yeah, all that sliding in and out takes it's toll...let us know how it holds up.

02-28-2015, 08:54 PM	#61
qtrmile2 Junior Member Join Date: Jan 2008 Location: Moscow Mills.Mo. Posts: 74 Likes: 0 Liked 9 Times in 4 Posts	Re: 1967 camaro A/S project More progress pics from today. Tim and Garrett working on the brake lines __________________ Tostoracing Retired S/ST and Stock owner/Driver Div. 5 Tech certification team

02-28-2015, 09:22 PM	#62
qtrmile2 Junior Member Join Date: Jan 2008 Location: Moscow Mills.Mo. Posts: 74 Likes: 0 Liked 9 Times in 4 Posts	Re: 1967 camaro A/S project Today progress Part 2 __________________ Tostoracing Retired S/ST and Stock owner/Driver Div. 5 Tech certification team

02-28-2015, 09:32 PM	#63
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: 1967 camaro A/S project Where did you get that carbon fiber roll bar padding? Seriously, car looks fantastic! __________________ Rich Taylor I/SA - 321

02-28-2015, 09:44 PM	#64
TOSTO RACING Senior Member Join Date: May 2007 Location: DRAGSTRIP Posts: 886 Likes: 885 Liked 652 Times in 184 Posts	Re: 1967 camaro A/S project Jerry Bickel race cars here in town sells it! It's cool stuff ! Got some more done today got it rolling, my new lugnuts came in ,rear end all buttoned up, all front brake lines are on, steering wheel on , and all interior back in and done now , motor mounts in, and last but not least my new rear wheels lol just kidding, but I was thinking about seeing how these hook lol!! __________________ 5664 GHI/SA 1985 CAMARO RED H/SA 1985 CAMARO BLUE I/SA

03-01-2015, 10:54 AM	#65
Danny Ashley Member Join Date: Nov 2001 Location: Marion,In. Posts: 267 Likes: 60 Liked 110 Times in 29 Posts	Re: 1967 camaro A/S project I like the look of the carbon fiber roll bar protector bit I'm not sure if it meets the rule book specifications for padding. It reads: Adequate padding must have minimum1/4-inch compression or meet SFI Spec 45.1. I don't see how carbon fiber can be used as a padding as it doesn't compress. The Bickle site doesn't say this protector meets the SFI spec. I can see using it on the side bar to protect from scratches, but not in the head area as it offers no protection. Do you plan to use a different padding for the head area? Am I missing something here? Last edited by Danny Ashley; 03-01-2015 at 11:02 AM.

03-01-2015, 12:08 PM	#67
Danny Ashley Member Join Date: Nov 2001 Location: Marion,In. Posts: 267 Likes: 60 Liked 110 Times in 29 Posts	Re: 1967 camaro A/S project Thanks Tim. After looking closer I see your 45.1 in the head area. Good luck this season and I'm enjoying following your build. Regards, Danny

03-01-2015, 01:10 PM	#68
impstocker Member Join Date: Dec 2008 Location: Wingdale, NY Posts: 302 Likes: 27 Liked 53 Times in 16 Posts	Re: 1967 camaro A/S project Nice Build. Question, are you using stock rubber bushings in your front upper control arms? I have solid bushings in my Impala, used solids in bottom too. Am I too "old school" Will Lamprecht 1965 Impala I/SA in progress.

03-01-2015, 06:52 PM	#70
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: 1967 camaro A/S project Yeah, all that sliding in and out takes it's toll...let us know how it holds up. __________________ Rich Taylor I/SA - 321

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode