|
|
04-29-2018, 10:19 PM | #1 |
Junior Member
Join Date: May 2011
Posts: 34
Likes: 0
Liked 8 Times in 3 Posts
|
Chevelle rear suspension
1971 chevelle need advice spinning rear tires current has drag bags 456 gear and 29-9-15
|
Liked |
05-08-2018, 09:08 AM | #2 |
VIP Member
Join Date: Jan 2003
Location: Allentown,PA
Posts: 2,447
Likes: 809
Liked 729 Times in 215 Posts
|
Re: Chevelle rear suspension
Probably would get more response on Stock /SS tech forum.
That said , this is one of the most worked out rear suspensions , lots of aftermarket parts available ,but can be made to hook like crazy with simple old school mods. If you don't have them bolt on upper "no hop " brackets are the starting point . they are necessary to get the 4 bar geometry to a usable intersection . Stock arms can be boxed and reinforced and solid bushings installed ,but there are so many aftermarket parts available with bearings or bushings it not worthwhile using the stock stuff unless you're on a really tight budget . Leave the rear anti roll bar on , disconnect or remove the front antiroll bar . Good front arm bushings are a must ,but if you are on a budget you can grind the serrations off the inner sleeve and just snug the bolt , allowing more freedom of movement . Good shocks are a must but , I've seen many an A body hook up great with just old school Chassis Engineering 3 way adjustable shocks. As far as springs go , good stock rear springs will suffice , the front springs should be replaced with longer, lighter springs with more stored energy from Moroso or Landrum . Use your air bags for preloading the right rear , good ballpark is 4-5 # left 10-15 #right ,if you need height,change the springs at use a cast aluminum spacer at the top. You can probably do most of the work for under $500.
__________________
Tom Goldman 1500 SG , 1506 STK |
Liked |
05-08-2018, 09:28 PM | #3 |
VIP Member
Join Date: Oct 2013
Location: Gulf Breeze, FL
Posts: 1,655
Likes: 8
Liked 33 Times in 16 Posts
|
Re: Chevelle rear suspension
Some of what has been mentioned such as no-hops, but invest in a real anti-roll bar like a HRParts@Stuff and lose the airbags completely. The real trick is getting the front-end to work properly and no amount of tweaking on the other end will compensate for the other.
__________________
Rich Taylor I/SA - 321 |
Liked |
06-17-2018, 10:16 PM | #4 |
VIP Member
Join Date: Oct 2002
Location: Richmond Indiana
Posts: 1,197
Likes: 5
Liked 32 Times in 19 Posts
|
Re: Chevelle rear suspension
Cheap Lakewood Bolt on traction bars work very well with single air bag on rt in spring.
Loose front shocks and check travel length. Very basic but helped my wagon |
Liked |
06-27-2018, 04:40 PM | #5 | |
Senior Member
Join Date: Dec 2008
Location: Berthoud, Coloraduh
Posts: 695
Likes: 13
Liked 8 Times in 7 Posts
|
Re: Chevelle rear suspension
Quote:
you surely don't mean Lakewood bolt on ladder bars do you:? had those POS's on a 66 Chevelle, bound up the rear end so bad, no amount of exlax could fix it....
__________________
without losers,winning means nothing. |
|
Liked |
07-15-2018, 09:37 PM | #6 |
VIP Member
Join Date: Oct 2002
Location: Richmond Indiana
Posts: 1,197
Likes: 5
Liked 32 Times in 19 Posts
|
Re: Chevelle rear suspension
These were an add-on type. did not replace any component. the 4 rear bars were the same just new rubber parts. Rear of bar bolts on frame and bumper hits under frame 32 inchs forward.
|
|
|