|
|
![]() |
#1 |
Senior Member
Join Date: Aug 2004
Location: Jacksonville, Florida
Posts: 803
Likes: 7
Liked 20 Times in 12 Posts
|
![]()
What p/v clearance in the min you run in a sbc automatic stocker? Also what valve spring pressures do you recommend on the seat and open? Thanks for the help
|
![]() |
![]() |
![]() |
#2 |
Junior Member
Join Date: Dec 2021
Location: Pukwana SD
Posts: 72
Likes: 217
Liked 10 Times in 8 Posts
|
![]() |
![]() |
![]() |
Liked |
![]() |
#3 |
Member
Join Date: Jan 2004
Location: Belmont N.S. Canada
Posts: 465
Likes: 223
Liked 148 Times in 67 Posts
|
![]()
Used run .035/.050 in my 350/255 using a 1409x at 200 on the seat. Reliefs stayed clean but no mechanical touchy feely
__________________
Chris Chapman 1969 Chevelle NHRA F-G/SA 1090 |
![]() |
![]() |
Liked |
![]() |
#4 |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 2,998
Likes: 693
Liked 1,467 Times in 548 Posts
|
![]()
There are many variables to take into consideration.
If you degree the cam with no valve train load, you have to compensate the P/V because the cam will retard 2 to 4 degrees when you start up the engine and the reason for running a tighter piston to valve clearance on the intake side. I like to run a tighter clearance on the intake side than on the exhaust side. Also, take into consideration the camshaft profile and lifter type you are running for valve spring pressure. In some profiles, you do not need high spring pressures. |
![]() |
![]() |
Liked |
![]() |
#5 | |
VIP Member
Join Date: May 2006
Location: Murfreesboro TN
Posts: 4,969
Likes: 1,134
Liked 1,218 Times in 313 Posts
|
![]() Quote:
You need to talk to your cam grinder about valve spring pressure, there's no way to tell you what you need without knowing the lobe profiles. The aggressive lobes will often want 200# on the seat, and maybe a 500# per inch spring rate.With those pressures, you're going to need 7/16" rocker studs, minimum, and 3/8" x 0.125" wall pushrods. That assumes you have light valvetrain components, such as hollow stem valves and light weight tool steel retainers. For piston to valve clearance, on the intake side, you can run your total deck clearance, plus 0.010" for a safety margin.On the exhaust side, you'll want 0.065" or more. You want to check that with your as raced valvetrain, and a dial indicator on the retainer. Also, those numbers assume you have good engine RPM control. And that doesn't mean using a rev limiter to control RPM on the burnout. Ask Pro Stock legend David Reher what he thinks about valvetrain behavior on the rev limiter.
__________________
Alan Roehrich 212A G/S |
|
![]() |
![]() |
Liked |
![]() |
#6 |
Senior Member
Join Date: Aug 2004
Location: Jacksonville, Florida
Posts: 803
Likes: 7
Liked 20 Times in 12 Posts
|
![]()
Thank You all for the helps and suggestions.
|
![]() |
![]() |
![]() |
#7 |
VIP Member
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,394
Likes: 492
Liked 722 Times in 278 Posts
|
![]()
https://rehermorrison.com/tech-talk-...g-your-engine/
I think this might be the David Reher comment Alan was talking about.
__________________
Adger Smith (Former SS) |
![]() |
![]() |
Liked |
![]() |
#8 |
Junior Member
Join Date: Aug 2015
Posts: 50
Likes: 10
Liked 9 Times in 5 Posts
|
![]()
I always wondered though with P/V what about actual P/V with heat in the motor vs cold I know some guys are are actually running the motors and then degree the cam as an actual hot running motor.
|
![]() |
![]() |
![]() |
#9 |
Member
Join Date: Sep 2016
Location: Monroe Twsp, NJ
Posts: 180
Likes: 229
Liked 313 Times in 70 Posts
|
![]()
Non coated lifters/cast cam vs coated lifters/billet cam, i was able to go from 180#s to 220-240#
__________________
Pat Clemente #1427 B/S |
![]() |
![]() |
![]() |
|
|