CLASS RACER FORUM
Page 4 of 4 « First 23 4
Show 40 post(s) from this thread on one page

CLASS RACER FORUM (https://classracer.com/classforum/index.php)
-   Stock and Super Stock (https://classracer.com/classforum/forumdisplay.php?f=3)
-   -   Drag pak Challenger (https://classracer.com/classforum/showthread.php?t=21039)

Alan Roehrich 10-24-2009 06:43 AM
Re: Drag pak Challenger
 
Quote:
Originally Posted by X-TECH MAN (Post 146389)
I wish FARMER was still in charge.
Be extremely careful what you wish for. I seriously doubt that you'd love the next "benevolent dictator" you'd get from NHRA. I'm not sure anyone likes the one we have now, or any of his "deputies".

Bob Pagano 10-24-2009 08:20 AM
Re: Drag pak Challenger
 
Farmer......if only, at least with him in charge you knew where you stood. It was right or you were out. His way or the highway and there were no if and or buts

GUMP 10-25-2009 05:57 AM
Re: Drag pak Challenger
 
Quote:
Originally Posted by Bob Pagano (Post 146362)
NHRA did not allow the vettes to mount a 12 bolt like that, it was shot down long ago. Now it looks like anything goes.
The biggest problem with these cars is that the stock control arms swing in the wrong direction. The factory supplied this design. I can't see where its any better than what's under an earlier Corvette.

Take Care,

Daren

DonatoEng 11-04-2009 07:40 PM
Re: Drag pak Challenger
 
NHRA requires that the stock shock and spring mounts on the body must be used for an independent suspension conversion to solid axle in Stock. The Challenger uses these with specific locations for the upper and lower control arm mounting holes on the body and axle ends. The rear suspension layout is based on a production Chrysler vehicle
The Corvette has the odd spring setup to meet these requirements.

Chris "drooze" Wertman 11-09-2009 08:59 AM
Re: Drag pak Challenger
 
Quote:
Originally Posted by DonatoEng (Post 149728)
NHRA requires that the stock shock and spring mounts on the body must be used for an independent suspension conversion to solid axle in Stock. The Challenger uses these with specific locations for the upper and lower control arm mounting holes on the body and axle ends. The rear suspension layout is based on a production Chrysler vehicle
The Corvette has the odd spring setup to meet these requirements.
Thank you !

Thank you very much, I am not irritated by much. I have been irritated by all the items (not here) on this issue.

Thank you.....

Mack Reeves 11-09-2009 05:07 PM
Re: Drag pak Challenger
 
Quote:
Originally Posted by drooze (Post 150427)
Thank you !

Thank you very much, I am not irritated by much. I have been irritated by all the items (not here) on this issue.

Thank you.....

X2....... Mack #43

Sam Murray 11-11-2009 07:29 PM
Re: Drag pak Challenger
 
Makes Wiebe A body suspensions look stock!

SSGN 11-11-2009 07:44 PM
Re: Drag pak Challenger
 
Quote:
Originally Posted by Sam Murray (Post 150932)
Makes Wiebe A body suspensions look stock!
Enough said!


All times are GMT -4. The time now is 06:37 PM.
Page 4 of 4 « First 23 4
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.