HOME FORUM RULES CONTACT
     
   
   

Go Back   CLASS RACER FORUM > Class Racer Forums > Competition Tech


Reply
 
Thread Tools Display Modes
Old 03-27-2009, 05:19 PM   #1
art leong
VIP Member
 
Join Date: Dec 2001
Location: Richmond Hill, Georgia
Posts: 2,037
Likes: 0
Liked 1 Time in 1 Post
Default Plug gaps?

The motor I'm running is the first higher than stock (12.7 to 1) compression ratio motor I've done. I've always gapped the plugs at stock specs (on my stockers) or at .050 on our hemi stocker (30 years ago).
The stock specs for my motor (2.4ltr, 4 cyl dodge) are .045. Stock compression is 9.5 to 1.
I'm presently using stock champion plugs. What should my gaps be set at?
__________________
Art Leong 2095 SS
art leong is offline   Reply With Quote
Old 04-03-2009, 11:02 AM   #2
Jeff Lee
VIP Member
 
Jeff Lee's Avatar
 
Join Date: Jul 2007
Location: Anthem, Arizona
Posts: 2,766
Likes: 0
Liked 2 Times in 2 Posts
Default Re: Plug gaps?

The gap isn't an issue but the heat range will be. Just make sure you go colder than stock. Could be quite a bit.
__________________
Jeff Lee 7494 D/S '70 AMX
Jeff Lee is offline   Reply With Quote
Old 07-10-2009, 07:31 AM   #3
Evan Smith
Member
 
Join Date: Nov 2001
Location: Tampa
Posts: 404
Likes: 4
Liked 94 Times in 4 Posts
Default Re: Plug gaps?

Art,

I have tried everything from .035 to .070 on my Stocker with no difference either way in performance. I like the small gap, especially in forced-induction applications. In chassis dyno testing I've seen some flutter in the graphs at high rpm that I attribute to a slight misfire. It instantly goes away when we take down the plug gap.

BTW, Justin is a real nice guy.

Evan
__________________
Evan Smith 1798 STK
Evan Smith is offline   Reply With Quote
Old 07-17-2009, 02:37 PM   #4
Jim Wahl
Veteran Member
 
Jim Wahl's Avatar
 
Join Date: Jan 2002
Location: Central Florida
Posts: 6,470
Likes: 636
Liked 685 Times in 131 Posts
Send a message via AIM to Jim Wahl Send a message via Yahoo to Jim Wahl
Thumbs up Re: Plug gaps?

After talking to George Widuch, who built the engine in my Volare, he said the pendulum is swinging toward the lower gap specs. Dyno testing and on-track testing seem to bare out that theory that as long as your ignition system is up to snuff wider plug gap does not make more power. A plus to this is your plug wires will last longer and chances of a high RPM miss less likely. Jim
__________________
Jim Wahl....NHRA #2239 S/SS - IHRA # 8 Stock, D2 Stock Champion (forever I guess)
2019 Baby Gators Stock Champion
2009 D2 National Open Stock Champion
1981 D2 West Palm Beach LDRS SS Runner Up
Past President, Southern Stock / Super Stock Association.
SSSSA Forum Moderator
Jim Wahl is offline   Reply With Quote
Old 08-20-2009, 07:54 AM   #5
Ven302
Member
 
Ven302's Avatar
 
Join Date: Feb 2005
Location: Stoney Creek
Posts: 261
Likes: 40
Liked 28 Times in 6 Posts
Default Re: Plug gaps?

Way back, we found on some street supercharged cars that the "candles" seemed to be getting blown out as boost and of course rpm increased, the guys were using some plugs advertised to be "all the stuff"
some unobtanium material, 37 ground straps (get the picture) I swapped the plugs to an NGK race plug
R567X-x type of part number advised to gap at .025 and voila the lights stayed on!, Also in my Suburban
I had a local shop do a new exhaust (hate working on street stuff) they put some platinum whatsit plug at .065 gap, the truck would misfire towing on anything but a gentle acceleration (turtle). I put some non resistor autlite race plugs, 2 ranges colder and .030 side gap and the problem went away.
My point? Go at least two maybe three colder, you can find charts on how to read the strap for heat range, non resistor and keep the gap low there will be little gains in a big gap and much greater chance of misfire.
Ven302 is offline   Reply With Quote
Old 08-23-2009, 06:41 AM   #6
Adger Smith
VIP Member
 
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,344
Likes: 425
Liked 665 Times in 258 Posts
Default Re: Plug gaps?

Just thought I would post some links to plug reading.

http://www.empirenet.com/pkelley2/sparkplugreading.html

http://www.dragstuff.com/techarticle...ark-plugs.html

http://www.4secondsflat.com/Spark_plug_reading.html

For those that like video:



You might keep in mind the pickup clearance plays a part in the rise time of the signal going to the ignition box. Too much clearance and the pickup will read a short spike from the magnet. To little clearance and it will cause a longer dwell & confuse the signal the box sees at High RPM.
__________________
Adger Smith (Former SS)

Last edited by Adger Smith; 08-23-2009 at 06:47 AM. Reason: SP
Adger Smith is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:46 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.