Wheel Studs - Page 2

SDT1DYI · 02-27-2019, 10:47 PM

Both the Dorman # unfortunately are .657 knurl diameter. The Moser are .685.

FED 387 · 02-28-2019, 01:58 AM

look at Speedway motors part #91005960--its a 5/8-11----- 4 inches long with a .685 knurled --you will haft change lug nuts but this should solve your problem --$13.99 set of 5--- now all you have to do is get the appropriate nuts--FED 387

Larry Hill · 03-01-2019, 08:15 AM

Or send the axles back and have them drilled and taped for the big studs.

jmcarter · 03-01-2019, 09:11 AM

What Larry said...if you roam the pits you’ll note Stock Eliminator is about the only class you’ll even see many 1/2 inch studs. My car has a good 9 inch setup but surprisingly was built using the smaller studs, and after breaking two studs it was hard to even find some last weekend (thanks to Mike McMahan, the Valdosta r/u, for the loaners). Moser sells the whole 5/8 stud kit for $80 so is by far the way to go. Losing a rear slick is never a pretty picture.

SDT1DYI · 03-01-2019, 10:18 AM

Thanks for everyone's replys. I thinking I'm going to go the drill and tap the axles route . I want to keep the 5/8" 18TPI .
When ordering new axles, thread in studs is really the best way to go in my opinion.

Steve STK. 6380.

gsa612 · 03-01-2019, 11:52 AM

The moser #8080 kit is the answer,same deal as the M-W but cheaper.It comes with 2 sets of spacers,long ones for the bogarts,short for the thicker welds.If you look at the unthreaded center the OD is larger so it fits in the wheel hole.They list it as 3'',but it should work. gsa612

340Cuda · 03-01-2019, 12:37 PM

I hope I am wrong, but I think I have read somewhere that race axles can be very hard to drill and tap.

Mike Pearson · 03-01-2019, 12:45 PM

I don't know about Moser but Strange will drill and tap their axles from 1/2 to 5/8 as long as the have not been welded on, Studs tacked etc. I had mine done by Strange about ten years ago and the cost was minimal. They fit the wheels perfectly when I got them back. Turn around was very quick as well.

Hacksaw · 03-01-2019, 02:20 PM

Quote:

Originally Posted by Mike Pearson

I don't know about Moser but Strange will drill and tap their axles from 1/2 to 5/8 as long as the have not been welded on, Studs tacked etc. I had mine done by Strange about ten years ago and the cost was minimal. They fit the wheels perfectly when I got them back. Turn around was very quick as well.

Moser offers that service as well.

ss3011 · 03-01-2019, 04:27 PM

Just asking , but if 5/8 is .625" and your axles have a .685 knurl , how do you tap them for a 5/8 stud ?

02-27-2019, 10:47 PM	#11
SDT1DYI Member Join Date: Nov 2016 Location: Indianola Washington Posts: 353 Likes: 0 Liked 394 Times in 124 Posts	Re: Wheel Studs Both the Dorman # unfortunately are .657 knurl diameter. The Moser are .685.

02-28-2019, 01:58 AM	#12
FED 387 VIP Member Join Date: Jun 2006 Posts: 3,349 Likes: 316 Liked 280 Times in 150 Posts	Re: Wheel Studs look at Speedway motors part #91005960--its a 5/8-11----- 4 inches long with a .685 knurled --you will haft change lug nuts but this should solve your problem --$13.99 set of 5--- now all you have to do is get the appropriate nuts--FED 387 Last edited by FED 387; 02-28-2019 at 01:58 AM. Reason: spelling

03-01-2019, 08:15 AM	#13
Larry Hill Live Reporter Join Date: Oct 2004 Location: Hickory, Ky Posts: 10,269 Likes: 1,630 Liked 9,413 Times in 1,950 Posts	Re: Wheel Studs Or send the axles back and have them drilled and taped for the big studs. __________________ IHM Used Parts https://ihmusedparts.com 888-821-1817

03-01-2019, 09:11 AM	#14
jmcarter VIP Member Join Date: Dec 2008 Location: Richmond Hill GA (and Port Ludlow WA) Posts: 4,136 Likes: 1,967 Liked 2,680 Times in 852 Posts	Re: Wheel Studs What Larry said...if you roam the pits you’ll note Stock Eliminator is about the only class you’ll even see many 1/2 inch studs. My car has a good 9 inch setup but surprisingly was built using the smaller studs, and after breaking two studs it was hard to even find some last weekend (thanks to Mike McMahan, the Valdosta r/u, for the loaners). Moser sells the whole 5/8 stud kit for $80 so is by far the way to go. Losing a rear slick is never a pretty picture. __________________ Jim Carter 2340 Super Stock 2340 SST/2340 Stock

03-01-2019, 10:18 AM	#15
SDT1DYI Member Join Date: Nov 2016 Location: Indianola Washington Posts: 353 Likes: 0 Liked 394 Times in 124 Posts	Re: Wheel Studs Thanks for everyone's replys. I thinking I'm going to go the drill and tap the axles route . I want to keep the 5/8" 18TPI . When ordering new axles, thread in studs is really the best way to go in my opinion. Steve STK. 6380.

03-01-2019, 11:52 AM	#16
gsa612 Senior Member Join Date: Jan 2008 Location: 100th Meridian Posts: 570 Likes: 116 Liked 280 Times in 139 Posts	Re: Wheel Studs The moser #8080 kit is the answer,same deal as the M-W but cheaper.It comes with 2 sets of spacers,long ones for the bogarts,short for the thicker welds.If you look at the unthreaded center the OD is larger so it fits in the wheel hole.They list it as 3'',but it should work. gsa612 Attached Thumbnails

03-01-2019, 12:37 PM	#17
340Cuda VIP Member Join Date: Apr 2003 Location: Tulsa, Oklahoma Posts: 1,567 Likes: 3,146 Liked 677 Times in 290 Posts	Re: Wheel Studs I hope I am wrong, but I think I have read somewhere that race axles can be very hard to drill and tap.

03-01-2019, 12:45 PM	#18
Mike Pearson VIP Member Join Date: Mar 2007 Posts: 2,368 Likes: 555 Liked 1,640 Times in 507 Posts	Re: Wheel Studs I don't know about Moser but Strange will drill and tap their axles from 1/2 to 5/8 as long as the have not been welded on, Studs tacked etc. I had mine done by Strange about ten years ago and the cost was minimal. They fit the wheels perfectly when I got them back. Turn around was very quick as well. __________________ Mike Pearson 2485 SS

03-01-2019, 04:27 PM	#20
ss3011 Senior Member Join Date: Feb 2002 Location: Southeast Michigan Posts: 885 Likes: 63 Liked 221 Times in 102 Posts	Re: Wheel Studs Just asking , but if 5/8 is .625" and your axles have a .685 knurl , how do you tap them for a 5/8 stud ?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode