|
![]() |
#1 |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 893
Likes: 67
Liked 230 Times in 108 Posts
|
![]()
Is there any companies making tie bar style solid roller lifters for a Hemi or Big Block Chrysler engine ? Looking to avoid hurting pushrods when using high load valve springs .
|
![]() |
![]() |
![]() |
#2 |
VIP Member
Join Date: Jun 2006
Posts: 3,366
Likes: 388
Liked 298 Times in 158 Posts
|
![]()
I would look at Erson or Jesel then call both of them tell them what you are trying to accomplish and ask for their suggestions. We used Erson with a .225 offset to get the proper pushrod geometry. They work and only took about 3-4 weeks for them. Fed:&7
Last edited by FED 387; 12-11-2016 at 02:34 PM. Reason: Spelling |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 893
Likes: 67
Liked 230 Times in 108 Posts
|
![]()
I was hoping there was an off the shelf lifter , that someone was currently using . Someone else must be having the same problem of galling the ends of pushrods that I am having .
|
![]() |
![]() |
![]() |
#4 |
VIP Member
Join Date: Jun 2006
Posts: 3,366
Likes: 388
Liked 298 Times in 158 Posts
|
![]()
Have u talked to Trend about your problems
|
![]() |
![]() |
![]() |
#5 |
Member
Join Date: Mar 2013
Location: Greentown, IN
Posts: 113
Likes: 0
Liked 0 Times in 0 Posts
|
![]() |
![]() |
![]() |
![]() |
#6 |
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 389 Times in 168 Posts
|
![]()
Mine is not Chrysler, but my Isky RedZones were doing that to intake pushrods at the rocker. If yours is also hurting them at the rocker, this may help: My lifters had an oil hole just above the band machines around the lifter body. I used a 3 cornered file to add a small groove from that band, up to the oil hole. Simply put a little more oil up the offending pushrods. My intakes only hurt pushrods, but they were 1.8 ratio, my ex were just 1.55. Hope this might help yours.
__________________
Ed Wright 4156 SS/JA |
![]() |
![]() |
![]() |
#7 | |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 893
Likes: 67
Liked 230 Times in 108 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#8 |
Junior Member
Join Date: Nov 2007
Location: Maryland
Posts: 92
Likes: 3
Liked 0 Times in 0 Posts
|
![]()
Try MRL Performance. I've got a set in a small block with jesel rockers- don't even have to bush the block.
Eddie Bolton |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Feb 2002
Location: Southeast Michigan
Posts: 893
Likes: 67
Liked 230 Times in 108 Posts
|
![]() |
![]() |
![]() |
![]() |
#10 | |
Senior Member
Join Date: Dec 2001
Location: Elysburg, Pa
Posts: 701
Likes: 298
Liked 242 Times in 94 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
|
|