|
04-30-2024, 10:25 AM | #1 |
Junior Member
Join Date: Jul 2007
Posts: 92
Likes: 2
Liked 0 Times in 0 Posts
|
428 NHRA Stocker Rocker Arms
I was told NHRA may now be allowing aftermarket rocker arms (Similar to Harland Sharp Non-Adj) to be used in 428 Stockers, as a replacement ? I’m not finding it in the appendage like the Molnar Rods. Brent Lykins makes a nice non adjustable shaft system I’d like to use if this is indeed correct
|
04-30-2024, 10:53 AM | #2 |
Junior Member
Join Date: Aug 2008
Posts: 36
Likes: 19
Liked 13 Times in 9 Posts
|
Re: 428 NHRA Stocker Rocker Arms
Roller rockers have been legal in stock eliminator for quite some time.
|
Liked |
04-30-2024, 11:05 AM | #3 |
Junior Member
Join Date: Jul 2007
Posts: 92
Likes: 2
Liked 0 Times in 0 Posts
|
Re: 428 NHRA Stocker Rocker Arms
|
04-30-2024, 11:54 AM | #4 |
Member
Join Date: Dec 2001
Location: Covina, CA
Posts: 470
Likes: 81
Liked 69 Times in 15 Posts
|
Re: 428 NHRA Stocker Rocker Arms
Detailed specifications are quickly accessible through <http://www.classracerinfo.com/>.
__________________
Chuck Norton |
04-30-2024, 12:33 PM | #5 |
Junior Member
Join Date: Jul 2007
Posts: 92
Likes: 2
Liked 0 Times in 0 Posts
|
Re: 428 NHRA Stocker Rocker Arms
|
04-30-2024, 08:47 PM | #6 |
VIP Member
Join Date: May 2006
Location: Murfreesboro TN
Posts: 4,934
Likes: 1,006
Liked 1,093 Times in 286 Posts
|
Re: 428 NHRA Stocker Rocker Arms
Get it in writing from Pat Cvengros, or Dave Ley, but the basic intent of the roller rocker arm rule is that the rocker arm must bolt to the head without modification or machine work. I don't see where the rule specifies the method of adjustment, or that the aftermarket roller rockers must be non adjustable if the factory rockers were non adjustable. So you may not need to buy non adjustable rocker arms. I'd see what is available that I wanted, and then contact Pat and/or Dave.
__________________
Alan Roehrich 212A G/S |
04-30-2024, 09:25 PM | #7 | |
Junior Member
Join Date: Jul 2007
Posts: 92
Likes: 2
Liked 0 Times in 0 Posts
|
Re: 428 NHRA Stocker Rocker Arms
Quote:
|
|
04-30-2024, 09:51 PM | #8 |
VIP Member
Join Date: May 2006
Location: Murfreesboro TN
Posts: 4,934
Likes: 1,006
Liked 1,093 Times in 286 Posts
|
Re: 428 NHRA Stocker Rocker Arms
No problem.
__________________
Alan Roehrich 212A G/S |
05-01-2024, 08:26 AM | #9 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,304
Likes: 1,661
Liked 9,537 Times in 1,978 Posts
|
Re: 428 NHRA Stocker Rocker Arms
Don’t forget to get some really good rocker shafts. Sometimes the ends break off.
|
05-01-2024, 11:46 AM | #10 |
Senior Member
Join Date: Oct 2006
Posts: 524
Likes: 228
Liked 505 Times in 136 Posts
|
Re: 428 NHRA Stocker Rocker Arms
I currently have the T&D FE rockers and shafts and they work really well so far. My previous engine had POP (precision oil pump) rockers and I liked them also. If you use T&D, you need to use the street rockers because the race rockers are a paired set up with modified mounting and oil through the pushrods which is not stock on an FE.
__________________
Mike 7570 A/SA Last edited by Mike Gray; 05-02-2024 at 05:07 PM. |
|
|