|
09-13-2017, 09:30 AM | #1 |
Member
Join Date: Apr 2005
Location: san antonio tx
Posts: 255
Likes: 5
Liked 28 Times in 15 Posts
|
4L65E Swap
Anybody know if I can replace the 4L60E in my 2007 GMC Sierra with a 4L65E from another vehicle and still use the computer in my truck, are they compatible? Also what vehicles do I find 4L65E transmissions in? Thanks guys.
|
09-13-2017, 12:12 PM | #2 | |
VIP Member
Join Date: Oct 2008
Posts: 2,114
Likes: 1,078
Liked 180 Times in 110 Posts
|
Re: 4L65E Swap
Quote:
Check out PerformaBuilt Trans and look at their Towing Series trans. http://performabuilt.com/gm%20heavy%20hauler.html They can also help with the advice on the 4L65E swap. Dan |
|
09-13-2017, 12:19 PM | #3 |
VIP Member
Join Date: Oct 2008
Posts: 2,114
Likes: 1,078
Liked 180 Times in 110 Posts
|
Re: 4L65E Swap
Here is some swap Information from a 4L60E to 4L65E posting
1) The tailhousing has to be swapped off stock tranny because the one that comes on the L65 doesn't have mounting points for the torque arm. (its 6 bolts and took me 3 minutes to do.) 2) the manual shaft (aka the shift lever) that protrudes out of the side of the trans and gets hooked to the shift linkage must be swapped as the Holden/truck style shift lever is too long and hits the tranny tunnel. it's pretty simple, it's just a matter of popping the pan off and working the lever out from under the gear selector (the ratchet thing that moves as you select different gears.), then putting the stock 4L60E lever in it's place. i let a tranny guy do this step just for the sake of him knowing exactly how to do it and it took about 10 minutes. 3) Should have the same electrical connector and plug in and go. Last edited by Dan Fahey; 09-13-2017 at 12:22 PM. |
09-13-2017, 10:06 PM | #4 |
VIP Member
Join Date: Apr 2012
Location: Connecticut
Posts: 1,110
Likes: 1,166
Liked 660 Times in 283 Posts
|
Re: 4L65E Swap
[QUOTE=Dan Fahey;544975]Here is some swap Information from a 4L60E to 4L65E posting
2) the manual shaft (aka the shift lever) that protrudes out of the side of the trans and gets hooked to the shift linkage must be swapped as the Holden/truck style shift lever is too long and hits the tranny tunnel. it's pretty simple, it's just a matter of popping the pan off and working the lever out from under the gear selector (the ratchet thing that moves as you select different gears.), then putting the stock 4L60E lever in it's place. i let a tranny guy do this step just for the sake of him knowing exactly how to do it and it took about 10 minutes. If you do this yourself, take special care not to cut the seal while putting the shaft back in the case.There is a sharp edge on the shaft. Deburr as needed. Mike A114 P/SA Last edited by Mike Jones; 09-19-2017 at 07:48 PM. |
09-18-2017, 11:03 AM | #5 |
Member
Join Date: Apr 2005
Location: san antonio tx
Posts: 255
Likes: 5
Liked 28 Times in 15 Posts
|
Re: 4L65E Swap
Anybody know the code in the glove boxes for the heavier duty trans?
|
|
|