HOME MAGAZINE FORUM RULES SPONSORS CONTACT
     
   
   
 
Go Back   CLASS RACER FORUM > Class Racer Forums > Class Racer Builds

Reply
 
Thread Tools Display Modes
Old 04-15-2017, 09:55 PM   #61
HP HUNTER
Member
 
HP HUNTER's Avatar
 
Join Date: Feb 2012
Location: Colorado Springs
Posts: 326
Talking Re: 1971 Buick 455 GS F/SA G/SA Build

I finally got the exhaust side of my heads done. Although I'am not sure I have this right, so I have questions. On my BBC builds with conventional camshafts I've always wanted lazy low lift flow then have it come on after .300 lift and take off, this has always worked well for me. On my Buick I gained around 12 CFM @ .200 and 12 CFM @ .300 and about 10 CFM @ .400 and finally 9 CFM @ .466 peak lift, will this help me or hurt me?
__________________
NHRA Stocker Cranks
Crank Repair
Counter Weight Cutting
HP HUNTER is offline   Reply With Quote
Old 04-17-2017, 08:59 AM   #62
R. Thorne
Member
 
Join Date: May 2009
Posts: 102
Default Re: 1971 Buick 455 GS F/SA G/SA Build

I almost didn't answer this because there's not enough info to make a valid response ( again, where are the .100 flow figure improvements on intake & exhaust). Also, i don't know what was done to improve the intake or exhaust flow. You are definitely going to have a (seemingly) wilder cam with low lift flow increase. You will have more reversion, true, but, in my opinion, you are going to see a substantial performance increase. Ron.
R. Thorne is offline   Reply With Quote
Old 04-17-2017, 08:07 PM   #63
HP HUNTER
Member
 
HP HUNTER's Avatar
 
Join Date: Feb 2012
Location: Colorado Springs
Posts: 326
Default Re: 1971 Buick 455 GS F/SA G/SA Build

Quote:
Originally Posted by R. Thorne View Post
I almost didn't answer this because there's not enough info to make a valid response ( again, where are the .100 flow figure improvements on intake & exhaust). Also, i don't know what was done to improve the intake or exhaust flow. You are definitely going to have a (seemingly) wilder cam with low lift flow increase. You will have more reversion, true, but, in my opinion, you are going to see a substantial performance increase. Ron.
Ron, I will send you the flow numbers in .050 increments, I'm actually scared to to see the increase @ .100 lift on the exhaust. Intake to exhaust flow is roughly 67% @ peak lift.
__________________
NHRA Stocker Cranks
Crank Repair
Counter Weight Cutting
HP HUNTER is offline   Reply With Quote
Old 04-20-2017, 05:38 PM   #64
R. Thorne
Member
 
Join Date: May 2009
Posts: 102
Default Re: 1971 Buick 455 GS F/SA G/SA Build

Sorry for delay, Mark. As Mike Taylor, Adger Smith, and others have said total and/or average flow is more important than peak lift flow increase at the expense of lower lift flow. I did not see anything exorbitant in your low lift exhaust numbers. Frankly, there is probably more potential low lift available. There are, of course, ways around the reversion issue if that is what concerns you, but I don't think you will need it. In short, yes, IMO, it will help you. Ron.
R. Thorne is offline   Reply With Quote
Old 04-30-2017, 07:54 PM   #65
HP HUNTER
Member
 
HP HUNTER's Avatar
 
Join Date: Feb 2012
Location: Colorado Springs
Posts: 326
Default Re: 1971 Buick 455 GS F/SA G/SA Build

Heads are finally installed on the engine. I would not look forward to doing another set like this Now I've got to fit the intake which I could see taking a day to get a good fit, then its dyno time.
__________________
NHRA Stocker Cranks
Crank Repair
Counter Weight Cutting
HP HUNTER is offline   Reply With Quote
Old 05-12-2017, 09:13 PM   #66
HP HUNTER
Member
 
HP HUNTER's Avatar
 
Join Date: Feb 2012
Location: Colorado Springs
Posts: 326
Default Re: 1971 Buick 455 GS F/SA G/SA Build

My preliminary dyno results are in, peak HP so far is 513 HP/550TQ. I will be making some changes looking for more, I will post up the results when I get done. More work and more HP 522 now.
__________________
NHRA Stocker Cranks
Crank Repair
Counter Weight Cutting

Last edited by HP HUNTER; 05-16-2017 at 08:36 AM.
HP HUNTER is offline   Reply With Quote
Old 05-19-2017, 10:41 PM   #67
HP HUNTER
Member
 
HP HUNTER's Avatar
 
Join Date: Feb 2012
Location: Colorado Springs
Posts: 326
Default Re: 1971 Buick 455 GS F/SA G/SA Build

I finally finished the engine part of my F/SA build. I want to say thanks to the following people for their help.

Harold Bettes
Jim Lewis
John Lewis
Chris Skaling

Dyno test from before the engine had been gone through is on the first page of this thread, dyno test of the finished product below.
Attached Thumbnails
Click image for larger version

Name:	IMG_0058.JPG
Views:	212
Size:	138.2 KB
ID:	39623   Click image for larger version

Name:	IMG_0059.JPG
Views:	208
Size:	127.4 KB
ID:	39624   Click image for larger version

Name:	IMG_0071.JPG
Views:	129
Size:	132.5 KB
ID:	39625  

Click image for larger version

Name:	IMG_0072.JPG
Views:	115
Size:	116.3 KB
ID:	39626   Click image for larger version

Name:	IMG_0073.JPG
Views:	118
Size:	134.1 KB
ID:	39627   Click image for larger version

Name:	IMG_0076.JPG
Views:	148
Size:	149.1 KB
ID:	39628  

__________________
NHRA Stocker Cranks
Crank Repair
Counter Weight Cutting
HP HUNTER is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:38 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.Ad Management plugin by RedTyger