|
09-11-2017, 04:05 PM | #21 |
Member
Join Date: Nov 2005
Location: Waldorf Md
Posts: 222
Likes: 10
Liked 26 Times in 15 Posts
|
Re: Mopar thrust bearing failure
I don't see how the trans would have caused a rod bearing issue. What did the thrust look like at that point ? Are you using the same bearings as before ? Same clearances ? Just curious.
__________________
Bill Koustenis |
09-11-2017, 04:11 PM | #22 |
Junior Member
Join Date: Jun 2007
Location: canada
Posts: 6
Likes: 1
Liked 1 Time in 1 Post
|
Re: Mopar thrust bearing failure
I would think that BillK might be on to something here
Is this a new engine or has it run before without hurting the thrust bearing ? The reason I ask is I had a problem with a thrust bearing in a 350 Chevy years ago. The block had been align honed and when they cut the cap they cut it crooked and it was tilting the thrust bearing just slightly. Took me a while to figure it out. Did something change in your combination right before your thrust problem started ? Just thinking out loud [/QUOTE] |
09-11-2017, 04:15 PM | #23 |
VIP Member
Join Date: Jun 2006
Posts: 3,349
Likes: 326
Liked 280 Times in 150 Posts
|
Re: Mopar thrust bearing failure
Bent crank-- trans crooked---convertor ballooning--- insufficient oil / lubrication---dowel pins not zeroed in ---- Fed387
|
09-11-2017, 04:23 PM | #24 |
Senior Member
Join Date: Sep 2006
Location: Fulton County, PA
Posts: 533
Likes: 9
Liked 745 Times in 206 Posts
|
Re: Mopar thrust bearing failure
I agree the rod failure would be hard to pin on a trans issue. Not so with the thrust. 7 to 8 thou is a good number. Bump or pry the crank back and forth a few times before tightening the main cap and force the crank towards the front of the engine when torquing that cap down.
If the issue started after having the trans apart, I would have someone familiar with that unit in a race application look closely at it. Would be nice to run it on a trans dyno to verify pressures before putting it back in. |
09-11-2017, 04:51 PM | #25 |
Junior Member
Join Date: Jan 2015
Posts: 41
Likes: 4
Liked 1 Time in 1 Post
|
Re: Mopar thrust bearing failure
I wiped out the thrust bearing in my 340. After a lot of thought, I determined the failure came from
stacking the weight of the engine and transmission on the driveshaft at the hit. I had eliminated the engine mounts and was utilizing an engine plate and OEM transmission mount to locate the engine. After the crank repair, I added a fore and aft limiter. I've had harder launches since then and no sign of thrust failure. The first thing to identifying the culprit is asking, "What changed?" |
09-11-2017, 06:54 PM | #26 |
Junior Member
Join Date: Apr 2016
Location: Sapulpa, OK
Posts: 84
Likes: 93
Liked 165 Times in 27 Posts
|
Re: Mopar thrust bearing failure
One other thing was changed, weight of the car.
Was at 3640, now @ 3750. Crank is internally balanced with Mallory metal. This is why I elected to have it repaired. To avoid the cost of rebalancing another crank. Rob & Main bearings have been changed every time. I am going to change out the crankshaft this time & have the line bore checked & corrected if need be. Since I'm new to this type of racing, anyone want to recommend a crank shop? |
09-11-2017, 07:18 PM | #27 |
VIP Member
Join Date: Oct 2007
Posts: 1,095
Likes: 401
Liked 246 Times in 99 Posts
|
Re: Mopar thrust bearing failure
where are you located?
|
09-11-2017, 08:10 PM | #28 |
Junior Member
Join Date: Apr 2016
Location: Sapulpa, OK
Posts: 84
Likes: 93
Liked 165 Times in 27 Posts
|
Re: Mopar thrust bearing failure
|
09-11-2017, 10:07 PM | #29 |
VIP Member
Join Date: Oct 2007
Posts: 1,095
Likes: 401
Liked 246 Times in 99 Posts
|
Re: Mopar thrust bearing failure
|
09-12-2017, 12:15 AM | #30 |
Member
Join Date: Oct 2005
Location: N.S. CANADA
Posts: 498
Likes: 155
Liked 68 Times in 41 Posts
|
Re: Mopar thrust bearing failure
Make sure the hub is not bottoming out and pulling the flex plate to the converter.I had a simlair problem.had to put washers under the converter legs to pull it out of the crank.
__________________
1231 FS/D Drag Pak 1231 E/SA 71 Demon Kelly MacKay |
|
|