|
09-21-2015, 10:46 AM | #41 |
Member
Join Date: May 2010
Posts: 252
Likes: 272
Liked 84 Times in 42 Posts
|
Re: FS/H CobraJet Body In White Project
looks real good George. Where can I get a set of those spiffy Ford fender covers? One thing that was handy on the Holley EFI I used was that it hooked up to the stock temp sending unit.
__________________
Bob Tilton 568 FS/H |
09-21-2015, 11:20 AM | #42 |
Member
Join Date: Apr 2012
Location: Harrison Twp. MI
Posts: 108
Likes: 83
Liked 3 Times in 3 Posts
|
Re: FS/H CobraJet Body In White Project
Sweet George! get her done and do Indy next month... haha I know it's a lot easier said than done.
__________________
Sam Monteleone 3348 S/SS |
09-21-2015, 07:49 PM | #43 |
Junior Member
Join Date: Sep 2009
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
|
Re: FS/H CobraJet Body In White Project
Beautiful build!!
|
09-21-2015, 08:35 PM | #44 |
Junior Member
Join Date: Jan 2011
Location: Ottawa Ontario Canada
Posts: 18
Likes: 0
Liked 0 Times in 0 Posts
|
Re: FS/H CobraJet Body In White Project
Great progress George Looks great.
|
10-18-2015, 10:56 PM | #45 |
Member
Join Date: Nov 2002
Location: Michigan
Posts: 178
Likes: 6
Liked 346 Times in 31 Posts
|
Re: FS/H CobraJet Body In White Project
More progress on the CobraJet. Hooked up the laptop to the BigStuff ECU and started the engine today so I could check the cam crank advance number. My Browell bellhousing is ready to go in so hopefully I can get it in early this week and finish up a few details by next weekend.
4 inch aluminium driveshaft from Raven Engineering. Radiator and radiator hoses installed. View of carpet and seats from drivers side. I found a new carpet that did not have any cut outs in it. I then cut holes for the removable shifter covers. I fabricated a throttle cable bracket since I am no longer using the drive by wire. I fabricated a small aluminium bracket to hold the BigStuff air intake temperature sensor right above the throttle body opening. Here is the bracket to hold the electric water pump drive motor. From here you can see the Moroso pcv filter and the electric water pump drive motor. More photos at http://9500rpm.com/GWCJ/index.html.
__________________
George Wright https://9500rpm.com |
10-19-2015, 09:04 PM | #46 |
Member
Join Date: Apr 2012
Location: Harrison Twp. MI
Posts: 108
Likes: 83
Liked 3 Times in 3 Posts
|
Re: FS/H CobraJet Body In White Project
Looking good George!
__________________
Sam Monteleone 3348 S/SS |
10-26-2015, 11:24 PM | #47 |
Member
Join Date: Nov 2002
Location: Michigan
Posts: 178
Likes: 6
Liked 346 Times in 31 Posts
|
Re: FS/H CobraJet Body In White Project
More progress. The Jerico and Long shifter are now in. The car was scaled. It weighs 3010 pounds with me in it (no weigh box). The pinion angle was set. The pre-load was set using the anti roll bar. Tomorrow I will check and set the front end alignment. Still need to carpet the rear seat area, but that wont stop me from testing the car. Hope to test it this coming weekend.
__________________
George Wright https://9500rpm.com |
10-27-2015, 10:21 AM | #48 |
Member
Join Date: May 2010
Posts: 252
Likes: 272
Liked 84 Times in 42 Posts
|
Re: FS/H CobraJet Body In White Project
Looks great George. I do like the blue. I've had a question ever since I saw this was going to be a manual trans. I know you are using a 4 speed but did Ford "offer" a 5 speed version also?
__________________
Bob Tilton 568 FS/H |
10-27-2015, 10:34 AM | #49 | |
Member
Join Date: Nov 2002
Location: Michigan
Posts: 178
Likes: 6
Liked 346 Times in 31 Posts
|
Re: FS/H CobraJet Body In White Project
Quote:
Yes. The Liberty LSC5100 was available.
__________________
George Wright https://9500rpm.com |
|
10-27-2015, 05:23 PM | #50 |
Junior Member
Join Date: Jan 2011
Location: Ottawa Ontario Canada
Posts: 18
Likes: 0
Liked 0 Times in 0 Posts
|
Re: FS/H CobraJet Body In White Project
Looking good George...Hope the testing goes well.. let us know ...
Bob |
|
|