|
|
11-18-2017, 01:30 PM | #1 |
Junior Member
Join Date: Mar 2008
Location: cicero n.y.
Posts: 29
Likes: 7
Liked 0 Times in 0 Posts
|
70 Javelin with mopar 8 3/4
I am building a 70 Javelin forNHRA
stocker ,I installed a mopar B body 8 3/4 rear and the center section it is offset.Will this cause any problems with the stock drivetrain.I am running a AMC 360 with a 727 trans.Should it be 0 offset ?
__________________
Rich Freitag 1440 SS Last edited by rich freitag; 11-18-2017 at 09:16 PM. |
11-18-2017, 02:21 PM | #2 |
Senior Member
Join Date: Mar 2002
Location: TN
Posts: 514
Likes: 355
Liked 204 Times in 72 Posts
|
Re: 70 Javelin with mopar 8 3/4
Mopar offsets the drive train 1 inch to the right (passenger side). If AMC has the drive train centered that is where the pinion should be. You should measure and set the pinion so there is no side to side angle. The only angle you should have is down. If you haven't spent much on the 8 3/4 I would put a Dana 60 in the car. It is stronger and faster.
Good luck.
__________________
Rod Greene Real men shift for them selves. Slowly working on TA Challenger for D,E/S and a 72 Challenger for SS/K, L as if I don't have enough other projects. |
11-18-2017, 03:03 PM | #3 |
VIP Member
Join Date: Nov 2001
Location: Florida
Posts: 1,538
Likes: 34
Liked 132 Times in 48 Posts
|
Re: 70 Javelin with mopar 8 3/4
If building a class car and it's available, a 904 is faster than a 727. Chrysler did some testing back in the '70's and it was about .15, all else being equal, plus you'll have the option of a less expensive 2.74 low gear set from a later trans.
General question - since the pinion is offset in Mopars with similar drivetrains & suspension, would matter if it was in an AMC or Mopar body?
__________________
LOCOMOTION Racing |
11-19-2017, 10:29 AM | #4 |
Senior Member
Join Date: Jul 2014
Posts: 561
Likes: 33
Liked 47 Times in 32 Posts
|
Re: 70 Javelin with mopar 8 3/4
Just to clearly, an 8-3/4 is not offset (center section) it's the pinion. Whereas the Dana is offset (center section) because the pinion is not as offset as the 8-3/4. I would like to see how many tenths of a horse power you would lose by being "not centered" when the up and down movement (car separation) is astronomical. Now if you're running a four link, go for it.
Mike Last edited by Coleydog; 11-19-2017 at 10:31 AM. |
11-20-2017, 09:36 AM | #5 |
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,980
Likes: 52
Liked 724 Times in 177 Posts
|
Re: 70 Javelin with mopar 8 3/4
I would use a Dana 60 rather than the 8 3/4.
__________________
|
12-01-2017, 03:22 AM | #6 |
Junior Member
Join Date: Jan 2007
Location: Md
Posts: 23
Likes: 0
Liked 1 Time in 1 Post
|
Re: 70 Javelin with mopar 8 3/4
An 8.75 isn't much stronger than an AMC-20 with 1 piece axles.
I ran for years with Henrys Axles, an AMC left hand thread TwinGrip & 4.44's and the tubes welded in. (390/4sp D/Stock). Ron. |
Thread Tools | |
Display Modes | |
|
|