|
07-07-2017, 07:33 AM | #1 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,278
Likes: 1,636
Liked 9,455 Times in 1,957 Posts
|
Driver Safety
I was working on a race car yesterday and noticed a daylight source in the trunk of the car. Who ever installed the rear fire wall did not do the job according to the safety standards in the NHRA rule book. Where the roll cage went through the package tray using the factory speaker holes, the fire wall was omitted. This would not be a problem until........things get out of control, and then its burn baby burn.
The point of this post is to bring attention to all racers that should be looking at their cars with a very critical eye. A good motto to use during inspection " That will do usually won't " With Tech reduced there will be fewer skilled eyes looking at our cars pointing out omissions that could affect the rest of our life. Be proactive on safety, your life may depend on it! Got to get back to work , Indy is only a few days away! |
07-07-2017, 08:24 AM | #2 |
Member
Join Date: Jul 2012
Location: Phoenix, Az
Posts: 320
Likes: 17
Liked 116 Times in 40 Posts
|
Re: Driver Safety
Very good point Larry. But when installing the sheet metal around the bar you cant get it perfect. What is the best thing, (sealer), to use to fill in the gap?
__________________
U/SA 79 Mustang |
07-10-2017, 12:02 PM | #3 |
Junior Member
Join Date: Dec 2001
Posts: 89
Likes: 0
Liked 8 Times in 4 Posts
|
Re: Driver Safety
The genius who decided tech is a waste of time and figured the organization could save money by cutting back on techmen has put racers in danger. Be warned that it is now up to you to look closer at your car and figure out how you can get hurt or worse. The extra set of eyes that could have possibly found a potentially dangerous issue is no longer looking at your car.
|
07-10-2017, 01:42 PM | #4 |
Member
Join Date: Oct 2003
Location: Lower Slower Delaware
Posts: 493
Likes: 14
Liked 199 Times in 74 Posts
|
Re: Driver Safety
Cut a square or rectangle of the same sheet metal then cut a hole in it the same size as the roll bat tube, cut it in half then rivet it in place tight to the tube.
__________________
Frank Ferrucci ?/SA 1271 |
07-10-2017, 01:47 PM | #5 |
VIP Member
Join Date: Jun 2006
Posts: 3,349
Likes: 328
Liked 280 Times in 150 Posts
|
Re: Driver Safety
Flexible lip seal grommets from Kennard industries or McMaster Carr-also can use weatherstripping glued into place or a paintable sealer from auto paying supply
Last edited by FED 387; 07-10-2017 at 01:48 PM. Reason: Spelling |
07-10-2017, 07:51 PM | #6 |
VIP Member
Join Date: Apr 2002
Location: Coarsegold, CA
Posts: 1,017
Likes: 57
Liked 321 Times in 101 Posts
|
Re: Driver Safety
Red FireStop calk in a calking gun
__________________
Bob Mulry 7516 STK A & M Motorsports |
07-10-2017, 08:01 PM | #7 |
VIP Member
Join Date: Mar 2007
Posts: 2,320
Likes: 546
Liked 1,629 Times in 502 Posts
|
Re: Driver Safety
The red fire stop caulk would not be a good choice. It does not have much of an adhesive quality. It is mostly a filler for non moving joints. I don't think it would stay in place in this application. There are some silicone based caulks that are fire rated. These can be obtained from a commercial sealant supplier
__________________
Mike Pearson 2485 SS |
07-11-2017, 07:54 AM | #8 |
Member
Join Date: Jul 2012
Location: Phoenix, Az
Posts: 320
Likes: 17
Liked 116 Times in 40 Posts
|
Re: Driver Safety
I found some Fire Block sealer at Lowes thats good to 1300 degs. I bought a tube of it to see if it would work.
__________________
U/SA 79 Mustang |
|
|