|
12-06-2019, 03:03 PM | #261 |
Senior Member
Join Date: Dec 2002
Posts: 867
Likes: 916
Liked 603 Times in 176 Posts
|
Re: Dumbo The Flying Elephant
I would think that at 45 psi you could create leaks that normally would not exist. Check the oil drain back hole near the block water drain plugs. That is where the aluminum blocks have been known to leak water.
|
12-06-2019, 04:04 PM | #262 |
Member
Join Date: Apr 2006
Location: canada
Posts: 244
Likes: 26
Liked 40 Times in 19 Posts
|
Re: Dumbo The Flying Elephant
Maybe try using antifreeze vs water for testing. That stuff will find its way out of places water won’t.
|
Liked |
12-09-2019, 08:10 AM | #263 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,270
Likes: 1,631
Liked 9,422 Times in 1,951 Posts
|
Re: Dumbo The Flying Elephant
Tried to installed new front cover, cam basket would not allow cover to seat against block. Going to machine cover for clearance, sounds easy. Just need to figure distance between cam and crank center line. Set mill up with riser blocks, 90* fence, remove front seal to pick up crank center line. Install bore head, fab tool, cut case 5.062 OD X 4.625 ID .060 deep on cam center-line. Piece of cake!
Reused old cover after inspection and cleaning with new seal. The block, heads, and water pump were holding 45# pressure for 30 minutes when I quit last night. Time to see if it leaked any last night, I'm crossing my fingers. |
Liked |
12-09-2019, 10:31 AM | #264 |
Member
Join Date: Oct 2002
Location: kansas
Posts: 229
Likes: 415
Liked 223 Times in 43 Posts
|
Re: Dumbo The Flying Elephant
Really appreciate your early morning reports. They remind me of what I need to get done.
Pete |
12-09-2019, 11:58 AM | #265 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,270
Likes: 1,631
Liked 9,422 Times in 1,951 Posts
|
Re: Dumbo The Flying Elephant
In 12 hours it looks like it lost approximately .1 lb. of pressure. Just one more case of assuming something is ready to be reused without being checked. Shame on Me!
I would say it was just another " Stupid old man trick " but I'm smarter than that. Just not that time. Last edited by Larry Hill; 12-09-2019 at 12:07 PM. |
Liked |
12-10-2019, 07:53 AM | #266 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,270
Likes: 1,631
Liked 9,422 Times in 1,951 Posts
|
Re: Dumbo The Flying Elephant
PRI rest of week
|
12-15-2019, 05:51 PM | #267 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,270
Likes: 1,631
Liked 9,422 Times in 1,951 Posts
|
Re: Dumbo The Flying Elephant
Got remotivated at the PRI. Thanks I needed that!
|
Liked |
12-15-2019, 06:16 PM | #268 |
VIP Member
Join Date: Oct 2005
Location: Schomberg, ON, Canada
Posts: 1,215
Likes: 1,522
Liked 334 Times in 132 Posts
|
Re: Dumbo The Flying Elephant
Ah yes - PRI.....Pause, Reflect, Invigorate......carry on.
__________________
Dave Turner #1153 |
Liked |
12-17-2019, 08:19 AM | #269 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,270
Likes: 1,631
Liked 9,422 Times in 1,951 Posts
|
Re: Dumbo The Flying Elephant
I'm Happy to report the water leak may have been the best thing to happen to the engine. On inspection found the crankshaft key had way to much ware for a few dyno pulls and two 1/8 passes. Grove in crank is .187 key is .183 making the key .004 small and allowing the soft key to be deformed by impact from crank gear and pump drive. I was advised to get correct size key made from better material.
As said by my Uncle Al " It doesn't coast a thing to pay attention" |
Liked |
12-17-2019, 09:45 AM | #270 | |
VIP Member
Join Date: Dec 2001
Location: phoenix
Posts: 1,406
Likes: 53
Liked 654 Times in 254 Posts
|
Re: Dumbo The Flying Elephant
Quote:
|
|
Liked |
Thread Tools | |
Display Modes | |
|
|