Need help restoring Super Trick and Motor Wheel finish - Page 2

2021STK · 06-07-2019, 09:20 PM

Thanks Dirk! You wouldn't happen to have his contact info you could PM to me?

chopperloco · 06-09-2019, 06:42 PM

I've spoken with Doug in the past,his rears were new old stock he found,the fronts are new Bogarts (brushed) ,with Super Trick caps...

2021STK · 06-12-2019, 02:51 PM

I stumbled onto a Ytube video today of the Moon Equip. Co. metal spinning their tanks and they refined the surface with sandpaper to give a satin finish.

Sounds like a good place to start on the Super Tricks, now all I need is a big lathe.

Thanks for all the suggestions and help.

Hacksaw · 06-12-2019, 04:15 PM

Quote:

Originally Posted by 2021STK

I stumbled onto a Ytube video today of the Moon Equip. Co. metal spinning their tanks and they refined the surface with sandpaper to give a satin finish.

Sounds like a good place to start on the Super Tricks, now all I need is a big lathe.

Thanks for all the suggestions and help.

In the 70's, I took my Super Tricks apart and bolted the outer to my Chrysler New Yorker"s rear hub. Had the fronts blocked and the other wheel on the ground. Spun her up and sanded my finger tips off. Just have to do the center areas by hand.

gsa612 · 06-12-2019, 06:11 PM

Quote:

Originally Posted by Hacksaw

In the 70's, I took my Super Tricks apart and bolted the outer to my Chrysler New Yorker"s rear hub. Had the fronts blocked and the other wheel on the ground. Spun her up and sanded my finger tips off. Just have to do the center areas by hand.

Ah yes,the "polish lathe"...lol. gsa612ski

Lee Jordan (3223) A/S · 06-14-2019, 08:20 AM

I work in a refinery and there are pipe cutting and threading tools used for small bore pipe there. They are open on one end so its easy to chuck the wheel in. Do this and clean all the oil and dirt first. Then use 320 grit or finer and let the machine turn as you "sand" it. You can control the finish because these machines turn slow. Did all four of mine and they looked brand new! Crager Super Tricks... With the clear coating gone, they are harder to keep looking that way but they can be coated again.

Lee.

Quote:

Originally Posted by 2021STK

I stumbled onto a Ytube video today of the Moon Equip. Co. metal spinning their tanks and they refined the surface with sandpaper to give a satin finish.

Sounds like a good place to start on the Super Tricks, now all I need is a big lathe.

Thanks for all the suggestions and help.

06-07-2019, 09:20 PM	#11
2021STK Member Join Date: Jun 2007 Posts: 281 Likes: 273 Liked 17 Times in 14 Posts	Re: Need help restoring Super Trick and Motor Wheel finish Thanks Dirk! You wouldn't happen to have his contact info you could PM to me? __________________ Dave Outten 2222 S/SS/SST/SG/HR 2021 S 1968 SS 1969 SR 1966 1990 Bracket

06-09-2019, 06:42 PM	#12
chopperloco Member Join Date: Feb 2011 Location: Ottawa,Ont.,CANADA Posts: 128 Likes: 103 Liked 69 Times in 16 Posts	Re: Need help restoring Super Trick and Motor Wheel finish I've spoken with Doug in the past,his rears were new old stock he found,the fronts are new Bogarts (brushed) ,with Super Trick caps...

06-12-2019, 02:51 PM	#13
2021STK Member Join Date: Jun 2007 Posts: 281 Likes: 273 Liked 17 Times in 14 Posts	Re: Need help restoring Super Trick and Motor Wheel finish I stumbled onto a Ytube video today of the Moon Equip. Co. metal spinning their tanks and they refined the surface with sandpaper to give a satin finish. Sounds like a good place to start on the Super Tricks, now all I need is a big lathe. Thanks for all the suggestions and help. __________________ Dave Outten 2222 S/SS/SST/SG/HR 2021 S 1968 SS 1969 SR 1966 1990 Bracket Last edited by 2021STK; 06-12-2019 at 02:54 PM.