|
02-21-2018, 01:52 PM | #1 |
Member
Join Date: Aug 2003
Posts: 238
Likes: 19
Liked 21 Times in 11 Posts
|
Thoughts on accepted aftermarket heads for 350?
I noticed there are accpeted RHS, Dart and Edelbroc heads for my combination.. What is everyones thought on going this route?
|
02-21-2018, 03:00 PM | #2 |
Member
Join Date: Dec 2006
Location: Charlevoix, MI
Posts: 421
Likes: 94
Liked 84 Times in 33 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
I was looking at them and the Dart look to be the best without going to the aluminum heads. We already found quite a pick up over the stock castings.
__________________
Bobby Lundholm 3516 G/SA |
02-21-2018, 03:10 PM | #3 |
Member
Join Date: Sep 2006
Location: Moncton, N.B.
Posts: 276
Likes: 24
Liked 24 Times in 13 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
Is/are the runner volumes going to be an issue.
Terry K |
02-21-2018, 03:13 PM | #4 |
Member
Join Date: Aug 2003
Posts: 238
Likes: 19
Liked 21 Times in 11 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
I was told you have to add 50# if you run them.. Just getting hard to find good cores for certain heads.. Mainly wondering if anyone went that route yet
|
02-21-2018, 03:35 PM | #5 |
Member
Join Date: Dec 2006
Location: Charlevoix, MI
Posts: 421
Likes: 94
Liked 84 Times in 33 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
I haven't heard anything about the runners yet. It depends on what class you run for the weight to be added. It's a 5 hp penalty across the board.
__________________
Bobby Lundholm 3516 G/SA |
02-21-2018, 03:38 PM | #6 |
Member
Join Date: Mar 2003
Location: cincinnati ohio
Posts: 205
Likes: 184
Liked 190 Times in 31 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
Unless you are running Super stock and filling the ports none of these heads are going to meet the port cc. numbers. You just cannot mill enough off get from 175 to 161 cc . I know they are showing 172 cc but check 174/175 cc. Rick.
__________________
Rick Winchester Stk 3277 |
02-21-2018, 03:43 PM | #7 |
Member
Join Date: Dec 2006
Location: Charlevoix, MI
Posts: 421
Likes: 94
Liked 84 Times in 33 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
Then if you can't adjust the runners because that's illegal and you can't leave them as is because they have to reflect stock runner numbers how would they be able to kick you out if you are running the spec head they approved?
__________________
Bobby Lundholm 3516 G/SA |
02-21-2018, 09:29 PM | #8 |
VIP Member
Join Date: May 2006
Location: Louisville , KY
Posts: 1,994
Likes: 63
Liked 270 Times in 68 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
The Edlebrock heads are 185 cc’s on the intake runner. Who approves this stuff?
__________________
Greg Hill 4171 STK |
02-21-2018, 10:09 PM | #9 |
VIP Member
Join Date: Jul 2007
Posts: 1,329
Likes: 883
Liked 720 Times in 151 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
Great thing about aluminum. You can weld it up, reprofile it, and cover it up. It will look like new and you probably pick up 30 hp at least. You have to do
something to keep up with the Mopars.
__________________
Todd Hoven 1035 Stock |
02-21-2018, 10:52 PM | #10 |
Junior Member
Join Date: Aug 2013
Posts: 28
Likes: 0
Liked 72 Times in 6 Posts
|
Re: Thoughts on accepted aftermarket heads for 350?
Question who actually submitted all these heads to NHRA or did NHRA pick them out. All these heads cc way to big to be used in stock.
|
|
|