HOME MAGAZINE FORUM RULES SPONSORS CONTACT
     
   
   
 
Go Back   CLASS RACER FORUM > Classifieds > Race Parts: Classifieds

Reply
 
Thread Tools Search this Thread Display Modes
Old 02-06-2018, 08:59 PM   #1
Don Fardie
Member
 
Don Fardie's Avatar
 
Join Date: Feb 2003
Location: Lakeville, Ma
Posts: 250
Default WTB Input Shaft for Jerico DR4

Looking to buy a Course spline (18 Mopar) Input Shaft for a DR4 Small Bearing Jerico
Thanks in advance!....Don
__________________
Don Fardie 1582 F/S
Don Fardie is offline   Reply With Quote
Old 02-07-2018, 09:26 AM   #2
Dwight Southerland
VIP Member
 
Dwight Southerland's Avatar
 
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 1,680
Default Re: WTB Input Shaft for Jerico DR4

Length?
__________________
Dwight Southerland is offline   Reply With Quote
Old 02-07-2018, 11:17 AM   #3
Don Fardie
Member
 
Don Fardie's Avatar
 
Join Date: Feb 2003
Location: Lakeville, Ma
Posts: 250
Default Re: WTB Input Shaft for Jerico DR4

Wasn't aware there were different lengths? I know there is a shorter version of the Jerico, but not the inputs. If that is the case it would be the input for the standard length Jerico.
__________________
Don Fardie 1582 F/S
Don Fardie is offline   Reply With Quote
Old 02-13-2018, 04:59 PM   #4
BILL TAYLOR
Junior Member
 
Join Date: Jan 2012
Location: In between cecil & the grove
Posts: 70
Default Re: WTB Input Shaft for Jerico DR4

Quote:
Originally Posted by Don Fardie View Post
Looking to buy a Course spline (18 Mopar) Input Shaft for a DR4 Small Bearing Jerico
Thanks in advance!....Don
Don, Are you looking for a Chrysler input or Chevy input w/18 splines?Bill Taylor.
BILL TAYLOR is offline   Reply With Quote
Old 02-14-2018, 05:16 AM   #5
james schaechter
VIP Member
 
Join Date: Dec 2004
Posts: 1,505
Default Re: WTB Input Shaft for Jerico DR4

Quote:
Originally Posted by Don Fardie View Post
Wasn't aware there were different lengths? I know there is a shorter version of the Jerico, but not the inputs. If that is the case it would be the input for the standard length Jerico.
Jerico inputs typically come in a length for a stand depth bell or a deeper bell that is one inch longer. May be they have custome lenths but I have not seen that.

The thing to watch is the type and version of the input. The early narrow gear DR4 is different than the small bearing wide gear DR4 vs the Big bearing wide gear DR4 vs the
DR4-4. Not to mention other versions that are not DR. Models. Of course, the pilot tip can be different as well.

The length of the trans won’t matter unless you are talking output shafts.

You might check to see what the case number is on your trans and call Scott at Jerico. They are not too expensive compared to used and you will get a new one. If you have an older model and can’t get one new, you need to do some research to be sure it is compatible. Hope this helps. Jim
__________________
James Schaechter 3163 STK
james schaechter is offline   Reply With Quote
Old 02-14-2018, 02:09 PM   #6
Don Fardie
Member
 
Don Fardie's Avatar
 
Join Date: Feb 2003
Location: Lakeville, Ma
Posts: 250
Default Re: WTB Input Shaft for Jerico DR4

Actually all set guys. I bought a back up Jerico and it is the early Narrow Gear and it came with a fine 26 spline. I switched over to the 18 Mopar set up when I went to the dual clutch. Dean Cook had one but had lent it out to someone and it was never returned. Well in looking on E-Bay the one I saw looked real close to one I had that I was using as an alignment tool. Bottom Line ...guess who had Deans Input shatft!!!!. My memory is good....it just a tad short LOL!!!
Thanks for all your help and input .......Don
__________________
Don Fardie 1582 F/S
Don Fardie is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 04:44 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright © Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.Ad Management plugin by RedTyger