GaraGE SALE

Bob Lasko · 12-02-2007, 04:05 PM

Chevy Bow Tie Cylinder Heads, 23 Degree Cast Iron. Prepared by Rons Porting Service in St,Charles,MO. Intake runners flow 300 cfm. Have 50cc chambers. have been angled milled 120. Intake and exhaust valves are Titanium, have bronze guides.K-motion 1.625 trip springs with titanium retainers. heads have been clearance for push rods.Heads have matching exhaust plates.These heads are only 3 years old and have only 45 runs. Have flow sheets. 2300.00 OBO.

Also have cam,pistons and rod that match these heads. 5.70 MGP rods and JE 4.125 bore pistons. Two extra. 800.00 obo

Bullet cam 762 lift. 225.00

With these heads cam and pistons made 632 hp

750 Holley Carburetor was done by Chuck Nuytten and is legal for for NHRA and IHRA Super mod and Econo classes. Has just been freshened.350.00 obo

SBC Bullet 50mm cam. Has 762 intake lift, 684 exhaust lift. Used only one season, about 40 runs. in excellent condition. 225.00

Three sets or Manley pushrods for small block chevy. 3/8 diameter, length 7.600, 7.675, and 7.794.

Fluidampr 6-1/4'' Diameter SB-Chevy Damper 175.00

MGP aluminum rods 5.70 inch, only 30 runs 350.00

Bill Miller aluminum rods 6.00 inch. Only 40 runs 200.00

K-motion Titanium Retainers 10 degree locks 150.00

K-motion 1500 trip springs 100.00

K-motion 1200 dubble springs 50.00

Call 203-858-1952 days, nites 203-834-0952 for any question or specs.

Bob Lasko 1134 SS/CS

12-02-2007, 04:05 PM	#1
Bob Lasko Senior Member Join Date: Jan 2002 Location: Wilton,CT Posts: 608 Likes: 0 Liked 168 Times in 49 Posts	GaraGE SALE Chevy Bow Tie Cylinder Heads, 23 Degree Cast Iron. Prepared by Rons Porting Service in St,Charles,MO. Intake runners flow 300 cfm. Have 50cc chambers. have been angled milled 120. Intake and exhaust valves are Titanium, have bronze guides.K-motion 1.625 trip springs with titanium retainers. heads have been clearance for push rods.Heads have matching exhaust plates.These heads are only 3 years old and have only 45 runs. Have flow sheets. 2300.00 OBO. Also have cam,pistons and rod that match these heads. 5.70 MGP rods and JE 4.125 bore pistons. Two extra. 800.00 obo Bullet cam 762 lift. 225.00 With these heads cam and pistons made 632 hp 750 Holley Carburetor was done by Chuck Nuytten and is legal for for NHRA and IHRA Super mod and Econo classes. Has just been freshened.350.00 obo SBC Bullet 50mm cam. Has 762 intake lift, 684 exhaust lift. Used only one season, about 40 runs. in excellent condition. 225.00 Three sets or Manley pushrods for small block chevy. 3/8 diameter, length 7.600, 7.675, and 7.794. Fluidampr 6-1/4'' Diameter SB-Chevy Damper 175.00 MGP aluminum rods 5.70 inch, only 30 runs 350.00 Bill Miller aluminum rods 6.00 inch. Only 40 runs 200.00 K-motion Titanium Retainers 10 degree locks 150.00 K-motion 1500 trip springs 100.00 K-motion 1200 dubble springs 50.00 Call 203-858-1952 days, nites 203-834-0952 for any question or specs. Bob Lasko 1134 SS/CS Last edited by Bob Lasko; 12-03-2007 at 06:37 PM.