|
12-29-2023, 06:18 PM | #1 |
Junior Member
Join Date: Feb 2006
Location: Westminster, CO
Posts: 52
Likes: 4
Liked 5 Times in 5 Posts
|
Blocking IAC on LT1 and re tune
I have blocked the IAC ports in my LT1 throttle body and was wondering the easiest way to get the idle air back through to get the right idle. I was going to adjust the blades out with the adjustment screws and reset the TPS in the ECU to zero. Is this the best way to do it or is their a better way to accomplish this? I am running a FAST XFI 2.0 ECU. Also is their any adjustment to the fuel map necessary in that lower end of the map? I am running AlphaN and sequential mode. Thanks in advance for the help.
|
12-29-2023, 07:07 PM | #2 |
Senior Member
Join Date: Jul 2003
Posts: 832
Likes: 631
Liked 912 Times in 333 Posts
|
Re: Blocking IAC on LT1 and re tune
If you have gotten used to a motor with a properly operating IAC, they have a tendency to spoil you. They will maintain and KEEP that idle at setpoint. Not very keen on Fast. You didn't mention if your dealing with a Superstocker or Stocker. Without the IAC the idles are a bit more contrary on the SS camshafts with their low vaacum, but very tunable. Yes, you will need to run the blades open and reset the TPS, especially with the Alpha.The issue you could possibly have is after getting it happy... so it will idle when cold and going into gear nicely (depending on the convertor)..., as it warms up the neutral idle will go higher than most people like. I build advanced tables so timing will be pulled out and or put in to maintain the desired RPM. The Holley has what they call "Idle Spark" to achieve this, but it only will move it 8 degrees one way or the other. I like 14 to do so,and it takes an advanced table. (If this is on a Stocker, you should not have any issues). Maybe someone with Fast knowledge will jump in here and help.
__________________
Jeff Niceswanger 3740 SS Last edited by Jeff Niceswanger; 12-29-2023 at 07:24 PM. |
12-29-2023, 07:25 PM | #3 |
Junior Member
Join Date: Feb 2006
Location: Westminster, CO
Posts: 52
Likes: 4
Liked 5 Times in 5 Posts
|
Re: Blocking IAC on LT1 and re tune
Jeff thanks for the info. Sorry, I forgot to mention it is a Stocker.There is a timing trim table for idle which allows up to 12 degrees adjustment related to target RPM vs Actual RPM. I can adjust with that I believe for temp variations.
Last edited by LS1Racer; 12-29-2023 at 07:48 PM. |
12-29-2023, 10:02 PM | #4 |
Senior Member
Join Date: Jul 2003
Posts: 832
Likes: 631
Liked 912 Times in 333 Posts
|
Re: Blocking IAC on LT1 and re tune
You should be good. Set your base idol at 20- 22 and let the trim do its thing.
__________________
Jeff Niceswanger 3740 SS |
12-29-2023, 10:36 PM | #5 |
Senior Member
Join Date: Nov 2003
Location: Donaldsonville, LA
Posts: 973
Likes: 9
Liked 196 Times in 66 Posts
|
Re: Blocking IAC on LT1 and re tune
You may also have to adjust numbers on the fuel map at idle. Generally adjusting the screw and/or the fuel map at idle you should be able to achieve idle.
__________________
Jimmy "Cooter" Hidalgo, Jr. 4865 E/SA '04 GTO 4865 SS/GA '99 Firebird |
Liked |
12-29-2023, 10:39 PM | #6 |
Member
Join Date: Mar 2013
Location: Italy, Texas
Posts: 154
Likes: 237
Liked 46 Times in 22 Posts
|
Re: Blocking IAC on LT1 and re tune
I built an adjustable air bleed to screw in where the IAC goes so I could leave the throttle blade closed at idle.
|
Liked |
12-30-2023, 08:08 AM | #7 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,465
Likes: 1,758
Liked 10,111 Times in 2,098 Posts
|
Re: Blocking IAC on LT1 and re tune
Might want to check with tech if the IAC adjuster replacement is below the throttle blades. The replacement could be viewed as an adjustable vacuum leak. Sometimes tech thinks a little differently than the racer.
|
Liked |
12-30-2023, 01:55 PM | #8 | |
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,651
Likes: 2,760
Liked 4,841 Times in 1,838 Posts
|
Re: Blocking IAC on LT1 and re tune
Quote:
Lang and co. had to call CA. for a ruling. They were told that the idle vacuum air had to be controlled by the computer, or not at all. It was okayed in Div 2 ,at that time. My Escort has an idle screw added instead of the stop screw on the throttle blades. (IAC disconnected) It works fine with the mild camshaft.
__________________
Real life never quite adds up.... Jay Farrar |
|
12-30-2023, 08:19 PM | #9 |
Senior Member
Join Date: Feb 2006
Posts: 635
Likes: 121
Liked 135 Times in 49 Posts
|
Re: Blocking IAC on LT1 and re tune
Just curious to why you remove the AIC and the benefits of this? I have Turbo Buicks and still use them with no ill effects. I know our cams are tiny in comparison to a stocker.
Thank for this post,very interesting.
__________________
The more people I meet the more I like my dog Kevin |
12-31-2023, 01:37 PM | #10 |
Junior Member
Join Date: Feb 2006
Location: Westminster, CO
Posts: 52
Likes: 4
Liked 5 Times in 5 Posts
|
Re: Blocking IAC on LT1 and re tune
I can only speak for my case so take this for what it is worth. My idle would race sometimes and was extremely wonky. I probably could have tuned it better but have read here many times from respected racers to just unplug it or block it. I chose just to block it. I do have another TB that still has an IAC on it if I decide to go back to it.
|
Liked |
|
|