Parting out 67 Fairlane D/SA-F/SA Stocker

RJ Sledge · 02-17-2018, 01:31 PM

Putting my 1967 Fairlane back to street condition, 390/320 motor, C4 2.75 transmission, ATI convertor, REF headers 1 7/8-2 1/8 with merge collectors, Aerospace brake system front and rear (dual caliper setup on rear), Weld AlumaStars front and back with Goodyear tires, Kirkey aluminum seats with black vinyl covers, Braille 21lb battery, etc..

390 motor has T&D Sportsman setup, Kuntz did the Edelbrock heads, hollow stem valves, beehive springs etc., Redline camshaft with Trend Perf lifters etc..
C4 transmission is torrington bearing throughout, aluminum drums, deep pan, 2.75 first gear.

Third members Nodular and Aluminum 4.63-5.29, R&P sets, Moser 35 spline rifle drilled profile milled axles and rear wheels are 4 3/4 BC as are the rear rotors....

Most all is new or never run, just built it and its been in my shop.

Anything that has to do with a D/SA-F/SA 67 Fairlane Stocker is forsale from this car so if i did not list it, just ask and I probably have it.

210-three seven three-40zero4 with any questions.

Thanks for looking

RJ Sledge

ron b · 02-17-2018, 07:14 PM

rj, any good shocks that also fit 68 mustang?

RJ Sledge · 02-18-2018, 03:27 PM

Ron I sent you a private message, respond by PM

RJ

HandOverFist · 02-19-2018, 06:38 PM

Where are you located?

6maverick9 · 02-20-2018, 09:50 AM

RJ I left you a message on the New FE forum, interested in the C4 bell, the brakes, and was all so wondering if you have any extra of the standard trim for a 67 Fairlane post car
Thanks

Jim Cimarolli · 02-21-2018, 10:19 PM

Hey Are Jay, would you happen to have one of those original Canadian built C4 transmissions that came in Mercury pickups?

Larry Hill · 02-22-2018, 03:57 PM

Well said Jim

Adger Smith · 02-25-2018, 01:35 PM

No Cimo, I don't think he has any of the Mercury Truck parts, but Are Jay has a shelf full of those Shelby rubber lobed camshafts for FE Fords.... You know the kind that check right on the spec then when you rev it up they get more lift and duration.

02-17-2018, 01:31 PM	#1
RJ Sledge Senior Member Join Date: Jun 2007 Posts: 750 Likes: 377 Liked 247 Times in 78 Posts	Parting out 67 Fairlane D/SA-F/SA Stocker Putting my 1967 Fairlane back to street condition, 390/320 motor, C4 2.75 transmission, ATI convertor, REF headers 1 7/8-2 1/8 with merge collectors, Aerospace brake system front and rear (dual caliper setup on rear), Weld AlumaStars front and back with Goodyear tires, Kirkey aluminum seats with black vinyl covers, Braille 21lb battery, etc.. 390 motor has T&D Sportsman setup, Kuntz did the Edelbrock heads, hollow stem valves, beehive springs etc., Redline camshaft with Trend Perf lifters etc.. C4 transmission is torrington bearing throughout, aluminum drums, deep pan, 2.75 first gear. Third members Nodular and Aluminum 4.63-5.29, R&P sets, Moser 35 spline rifle drilled profile milled axles and rear wheels are 4 3/4 BC as are the rear rotors.... Most all is new or never run, just built it and its been in my shop. Anything that has to do with a D/SA-F/SA 67 Fairlane Stocker is forsale from this car so if i did not list it, just ask and I probably have it. 210-three seven three-40zero4 with any questions. Thanks for looking RJ Sledge Last edited by RJ Sledge; 02-17-2018 at 01:34 PM.

02-17-2018, 07:14 PM	#2
ron b Member Join Date: Mar 2008 Posts: 123 Likes: 0 Liked 2 Times in 2 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker rj, any good shocks that also fit 68 mustang?

02-18-2018, 03:27 PM	#3
RJ Sledge Senior Member Join Date: Jun 2007 Posts: 750 Likes: 377 Liked 247 Times in 78 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker Ron I sent you a private message, respond by PM RJ

02-19-2018, 06:38 PM	#4
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,655 Likes: 8 Liked 33 Times in 16 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker Where are you located? __________________ Rich Taylor I/SA - 321

02-20-2018, 09:50 AM	#5
6maverick9 Junior Member Join Date: Nov 2015 Posts: 5 Likes: 0 Liked 0 Times in 0 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker RJ I left you a message on the New FE forum, interested in the C4 bell, the brakes, and was all so wondering if you have any extra of the standard trim for a 67 Fairlane post car Thanks

02-21-2018, 10:19 PM	#6
Jim Cimarolli Senior Member Join Date: Mar 2002 Location: Sulphur Springs Texas Posts: 728 Likes: 108 Liked 134 Times in 40 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker Hey Are Jay, would you happen to have one of those original Canadian built C4 transmissions that came in Mercury pickups?

02-22-2018, 03:57 PM	#7
Larry Hill Live Reporter Join Date: Oct 2004 Location: Hickory, Ky Posts: 10,269 Likes: 1,630 Liked 9,413 Times in 1,950 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker Well said Jim __________________ IHM Used Parts https://ihmusedparts.com 888-821-1817

02-25-2018, 01:35 PM	#8
Adger Smith VIP Member Join Date: Dec 2001 Location: Texarkana Ark/TX Posts: 2,349 Likes: 433 Liked 676 Times in 260 Posts	Re: Parting out 67 Fairlane D/SA-F/SA Stocker No Cimo, I don't think he has any of the Mercury Truck parts, but Are Jay has a shelf full of those Shelby rubber lobed camshafts for FE Fords.... You know the kind that check right on the spec then when you rev it up they get more lift and duration. __________________ Adger Smith (Former SS)

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode