|
02-25-2012, 09:59 AM | #41 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,778
Likes: 70
Liked 400 Times in 191 Posts
|
Re: Ken Keir wheelie bars
HP HUNTER should be along any minute now.
|
02-25-2012, 10:08 AM | #42 |
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 389 Times in 168 Posts
|
Re: Ken Keir wheelie bars
Why don't you just use your real name? And quit putting pictures of you cars in your posts? We have seen them, OK?
__________________
Ed Wright 4156 SS/JA Last edited by Ed Wright; 02-25-2012 at 10:11 AM. |
02-25-2012, 10:09 AM | #43 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,778
Likes: 70
Liked 400 Times in 191 Posts
|
Re: Ken Keir wheelie bars
I've been 1320racer on the net for a long long time, besides you know my name and I didn't read any rule from Ken stating that photos and/or videos weren't allowed in posts.
|
02-25-2012, 10:14 AM | #44 |
Senior Member
Join Date: Feb 2012
Location: Colorado Springs Colorado/Thousand Oaks Ca
Posts: 606
Likes: 68
Liked 238 Times in 97 Posts
|
Re: Ken Keir wheelie bars
Not sure about that, new to your forum. My question here is this, and its a very legitemit question thats needs a real answer, how does a 10.07 @ 131 = a 1.28 60, that car is not moving hard enough down low to run that, as evidenced by the 131 MPH. Pump gas, you on the forum look at the exhaust, it doesnt look like pump gas to me. Now you will say I have a problem with the performance, not so, compression (11.5), roller cam, single plane, big double pumper holley, ported heads, and so on, my goodness, I would hope the car could run a 10.07 especially at Atco. The car runs 9.89 @ 134 and change, again high MPH for the ET, certainly you would have a faster 60 with the 522, show us the time slip, certainly this is a fair request, put this to bed. Looks like the picture of the exhaust will have to wait till later, it will need to be resized.
|
02-25-2012, 10:19 AM | #45 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,778
Likes: 70
Liked 400 Times in 191 Posts
|
Re: Ken Keir wheelie bars
again...who are you?
That said, this thread ain't about my former ride, it's about wheelie bars specifically Ken Keir's single wheelie bar. I have advised my internet friend Garret aka 40Coupe on this matter the same as I have advised him for over 10 years. If you have nothing further to add to this thread by replying to the question asked and about the car in question and are only interested in my former ride and what it did 5 years ago, I suggest you start a new thread in the Bracket Racing Forum about it and be sure to include your real verifiable name. Oh and for the record...the 1.28 was not carded on the 10.07 pass which was at ETown NOT Atco, it was run at Piedmont Dragway as can be seen in the photo. The compression is 11:1 NOT 11.5 and the 522 was run then as it is now with a restrictor plate. Last edited by 1320racer; 02-25-2012 at 10:27 AM. |
02-25-2012, 10:26 AM | #46 | |
Senior Member
Join Date: Feb 2012
Location: Colorado Springs Colorado/Thousand Oaks Ca
Posts: 606
Likes: 68
Liked 238 Times in 97 Posts
|
Re: Ken Keir wheelie bars
Quote:
|
|
02-25-2012, 10:31 AM | #47 | |
Senior Member
Join Date: Feb 2012
Location: Colorado Springs Colorado/Thousand Oaks Ca
Posts: 606
Likes: 68
Liked 238 Times in 97 Posts
|
Re: Ken Keir wheelie bars
Quote:
|
|
02-25-2012, 10:34 AM | #48 |
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 1,778
Likes: 70
Liked 400 Times in 191 Posts
|
Re: Ken Keir wheelie bars
show us in that thread you're going to start all the 3900 lb. small tire Chevelles with a bolt on suspension that run 10.07 n/a with a nothing special 11:1 468 no mind 9.89 through a full exhaust and launched off the footbrake too. Don't forget to include detailed photos of every aspect of the car(s)
your request has been denied just as my request to stop hiding behind a screen name. Besides I like it better that you and those like you refuse to believe. No doubt you and I have been down this roads before years ago on another board(s). Last edited by 1320racer; 02-25-2012 at 10:39 AM. |
02-25-2012, 10:37 AM | #49 |
Senior Member
Join Date: Feb 2012
Location: Colorado Springs Colorado/Thousand Oaks Ca
Posts: 606
Likes: 68
Liked 238 Times in 97 Posts
|
Re: Ken Keir wheelie bars
I dont believe the 1.28 60, because of what Ive seen the car run, period. Sorry, would like to see a time slip.
|
02-25-2012, 10:38 AM | #50 |
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 389 Times in 168 Posts
|
Re: Ken Keir wheelie bars
10.07, 131, 1.28, those numbers are all in line for a decent run.
134 is not a big MPH for a 9.89 None of those are fast for big engines, however.
__________________
Ed Wright 4156 SS/JA |
|
|