Chevy Parts

[Bruce Noland]

Small Block 350 Chevy:
10 runs
Pair of 993 heads all best parts by Whitaker: $2,250.00
Short Block, +.065 bore, Coated CP Pistons, Total seal Rings, Bushed lifter bores with Schubeck Lifters, latest Bullet Cam, $1950.00
Intakes, 771,751 and 469 all professionally cleaned $275.00 each
Used ATI Balancer: $225.00

Also many more intakes, both two barrel and four barrel for 71/72/73 motors: $50.00 each
Vic Junior: $95.00
One bone stock Aluminum intake for 69 302/350: $495.00
Stock heads with original valves in place: Pair of 487 $275.00, Pair of 487X $325.00
Fresh Metric race transmission, forward pattern, $1,150.00
Fresh metric Torque converters: $275.00 each

350 Bracket motor, long block (everything but intake), TRW pistons, 993 heads with 2.02 Valves and Lunati crank: $1550.00

350 short block, Stocker 71/72 combo's, Ross pistons, Total Seal Rings, good Comp cam, Block has minor repair but still running strong when I built the 73 combo. Should be freshened: $1,150.00

Chevy Big Block:
Aluminum Intakes:
Two 359's for 454: $375.00 each
One 163 with cut plenum for All Big Blocks $325.00

Big "School Bus" Pan for Big Blocks. Cleaned with trap: $275.00

Big Block Buick 455 Block, cleaned deburred and magnafluxed. It's meant to be the premo block: $475.00.
Two pairs of Stage one heads: Cleaned and magnafluxed: Not sure what they are worth.


Assorted parts:
Two Holroyd Holley carburetors: Very nice condition. Cost $1,000.00+ each but will sell for $575.00 each.
Two like new Moroso 24" x 15" tires, eight passes on them $175.00 for pair
Two new Weld Aluma Star rear wheels: Slicks were monted on them but they would not fit my car. The slicks were removed and the wheels put back in boxes. GM pattern with 3 1/2" back spacing: $425.00 for pair.
New in box FluidDampr for small block Chevy: $175.00
NOS Camaro Hood, 70-81 with GM Stickers still in place. Three very small blemishes: $775.00.
Yamaha Generator - 6,500 Watt in great condition. These generators are selling for over $3,000.00 new. Will sell for $995.00.

All prices exclude freight:

Thanks for reading and Merry Christmas!

[J.R. Haddad]

Bruce, tell me about the torque converters, what motor were they behind, stall, shift points, fall back, etc. Merry Christmas!! J.R. Haddad.

[Bruce Noland]

For 350 270 motors. About 420 HP, at 3,450 pounds. All of them in the 5,150 - 5,200 range. Depending on gearing and class, I would shift at 6,500 and then 6,800 usually dropped back about 800 rpm. One PTC, two Dynamics and one AT I. The AT I is probably sold.

[Dwight Southerland]

Bruce - is it a flat top piston short block?

[PJ305]

Bruce , does the short block have c-19cp
pistons for the 73 model rated at 287hp . Thanks

[Bruce Noland]

The short block is for a 350/270 dish piston motor.

[J.R. Haddad]

Bruce, you need to clear some space to accept P.M.'s.
Thanks, J.R. Haddad.

[jon jamison]

Hi Bruce,
I'm interested in the 10 inch wheels. Please contact me at flowbenchguy@yahoo.com or call Seven12 three63 threeeight01
Thanks,]
Jon Jamison

[ZenzenRacing]

Info on the generator please.

[Bruce Noland]

Sorry guys. I thought this ad was burried. The ten wheels have been sold and I sent a pcture of the generator to zenzen. I will try to do a better job of keeping up with this ad in the future. Thanks.