|
![]() |
#551 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,402
Likes: 1,713
Liked 9,840 Times in 2,050 Posts
|
![]()
Got the honing plates on Dumbo with the crank still in the block to check cylinder straightness. Bottom line is we have to do something different, the cylinders were everywhere. .002 tight at 2-8 o’clock,10-4 slightly better, 12-6 loose tight loose, and 3-9 not bad.
I should have quit a little over a year after we started racing, because then I knew most of the answers! |
![]() |
![]() |
![]() |
#552 | |
VIP Member
Join Date: Nov 2002
Location: Massapequa Park,NY
Posts: 1,226
Likes: 1,777
Liked 849 Times in 275 Posts
|
![]() Quote:
__________________
1989 Camaro Iroc-Z I/SA B&B Auto Machine Shop. |
|
![]() |
![]() |
![]() |
#553 |
Senior Member
Join Date: Dec 2002
Posts: 881
Likes: 970
Liked 611 Times in 181 Posts
|
![]()
I believe that Larry has the Mopar aluminum block. I have had friends that faced the same problems. You can try to hone it straight, but after you run it, the dimensions are all over the place. 8 Darton sleeves would be the place to begin or take a 100 lb weight penalty and use the cast iron BGE block.
|
![]() |
![]() |
Liked |
![]() |
#554 | |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 2,997
Likes: 693
Liked 1,467 Times in 548 Posts
|
![]() Quote:
The best is Steve Demirjian at Racing Engine Development in California. He is also the Engine Shop Manager of Darton and one of the foremost experts in sleeving blocks holding many patents on engine sleeves. http://www.raceenginedevelopment.com...odge-6-1-hemi/ |
|
![]() |
![]() |
Liked |
![]() |
#555 | |
VIP Member
Join Date: Apr 2003
Location: Tulsa, Oklahoma
Posts: 1,600
Likes: 3,449
Liked 701 Times in 302 Posts
|
![]() Quote:
Hidden Horsepower episode on cylinder honing. However last time a checked and it is probably worse now, he had a thirteen week backlog on block work. |
|
![]() |
![]() |
![]() |
#556 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,402
Likes: 1,713
Liked 9,840 Times in 2,050 Posts
|
![]()
It maybe a case of the block is not strong enough for the cylinder pressure generated under full load. My guess, and it’s only a guess, that the cylinders balloon and contract every cycle and become not straight and out of round in time.
For now I’m learning the do’s and don’t of the engine. With few parts available I’m doing my best not to destroy anything. I believe better sleeves will change things. |
![]() |
![]() |
![]() |
#557 | |
Member
Join Date: Mar 2016
Location: Crete, IL
Posts: 167
Likes: 226
Liked 56 Times in 24 Posts
|
![]() Quote:
__________________
Todd Gross 3323 FS/E,F |
|
![]() |
![]() |
![]() |
#558 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,402
Likes: 1,713
Liked 9,840 Times in 2,050 Posts
|
![]()
With me weighing 300+ the iron block would have to make a lot more power for me to consider it. If it not on the list I can’t use it. I try to walk on the knife edge on the rules, but I always have a set of gaskets and I am fearless going to the barn. Been doing this 30 some years and have been good every time, but all it takes is one third of the thickness of a hair (.001”) on the wrong side of a number and I will be disqualified.
|
![]() |
![]() |
Liked |
![]() |
#559 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,402
Likes: 1,713
Liked 9,840 Times in 2,050 Posts
|
![]()
With the block having 16 main studs and location sleeves for the caps removing the caps quickly use to be difficult. Solution was a Gen III cap puller from Arrow. It’s great
|
![]() |
![]() |
Liked |
![]() |
#560 | |
Senior Member
Join Date: Apr 2020
Location: Phila, PA
Posts: 659
Likes: 0
Liked 584 Times in 315 Posts
|
![]() Quote:
Larry, If your weight and the car's weight does not change then all the iron block has to do is make enough HP to offset the difference in the weight between the 2 blocks. I do not know what the difference will be for those blocks. I do know that many years ago on a difference style engine / block making about 750 HP the iron block made about 15 more HP. Stan |
|
![]() |
![]() |
Liked |
![]() |
|
|