|
![]() |
#531 |
VIP Member
Join Date: Dec 2008
Location: Richmond Hill GA (and Port Ludlow WA)
Posts: 4,192
Likes: 2,115
Liked 2,918 Times in 898 Posts
|
![]()
Agree Frank, Larry and Marshall both have their cars doing amazing 60’ times.
__________________
Jim Carter 2340 Super Stock 2340 SST/2340 Stock Set another place at the table |
![]() |
![]() |
Liked |
![]() |
#532 | |
Member
Join Date: Aug 2013
Location: Howell, MI
Posts: 247
Likes: 685
Liked 224 Times in 74 Posts
|
![]() Quote:
Do you leak check with the engine dead cold or after running it?
__________________
Andy Friar |
|
![]() |
![]() |
![]() |
#533 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
Cold. it turned over to easy
|
![]() |
![]() |
Liked |
![]() |
#534 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
Back to Dumbo. On further tear down the pull down side of the crankpin needs to look just a little better. The bearings look great only one spot to look at and figure out why.
|
![]() |
![]() |
![]() |
#535 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
Now I have two spots on two different rods but the spots are in the same place, at the parting line where the wash, may not be the correct terminology, area is on the bearings. I found no sign of trash, burrs, or whiteness marks on rod i d or shell. CB663HXN
|
![]() |
![]() |
![]() |
#536 |
Member
Join Date: Aug 2010
Location: CT
Posts: 418
Likes: 1,363
Liked 297 Times in 128 Posts
|
![]()
Do the marks correspond with either end of the bolt? How far from the parting line are they?
__________________
Phil Molski PMR Performance S/C 1623 |
![]() |
![]() |
![]() |
#537 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
The the damage spots are on the upper bearing shell at the part line on the chamfered side of the rod. I got a double ball micrometer and checked thickness at the edge opposite the tang and the thickness change was.0018” in the width of .785”. Vertical clearance is fine, it just about a .125”wide spot that is protruding into the ID of the rod clearance area that is being removed mechanically exposing the steel bearing shell to the crankshaft
|
![]() |
![]() |
![]() |
#538 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
Ordered a new set of bearings so maybe I can make a good set out of two sets that I will have. Also have a set of AOL coming to look at and see what kind of clearance we will have.
Another shop kind enough to let me use their double ball micrometer to check my bearings. Wednesday I will have my own ball micrometer. My old drag racing advisor Richard Carter said “If you have to borrow something more than once, you need to get one” |
![]() |
![]() |
Liked |
![]() |
#539 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
I'm lucky enough to be able to call an engine professional and get their advice on how to proceed. The new ACL race bearings did pass our new incoming QC test for edge variance. I still have to check for clearance and weight difference for balance. The ACL parts a just a little bit wider than the CB663's.
|
![]() |
![]() |
![]() |
#540 |
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,391
Likes: 1,706
Liked 9,760 Times in 2,039 Posts
|
![]()
Got my new CB663 XXX bearings today but my new micrometer won’t be here until Wednesday. Odds should be in my favor that I get some good bearings.
|
![]() |
![]() |
Liked |
![]() |
|
|