|
![]() |
#11 | |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#12 |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]()
Pictures of rods. I will balance them next.
Last edited by MIKE JONES 302; 08-15-2018 at 10:40 PM. |
![]() |
![]() |
![]() |
#13 |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]() |
![]() |
![]() |
![]() |
#14 |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]()
Setting up for the line hone.
|
![]() |
![]() |
![]() |
#15 |
VIP Member
Join Date: Aug 2013
Posts: 1,766
Likes: 1,197
Liked 1,958 Times in 493 Posts
|
![]()
Nice progress.
__________________
Todd Greene |
![]() |
![]() |
![]() |
#16 |
Member
Join Date: Oct 2009
Location: Whitecourt,Alberta,Canada
Posts: 228
Likes: 4,113
Liked 46 Times in 25 Posts
|
![]()
Are you building for street or strip ? Higher quality rods would be a good idea. I have spun my Original 69 Z28/RS to 7200rpm on many occasions, but that is playing with fire. On one of my 302 engines in my Super Stock car I have spun it too well over 9000.
__________________
Bruce Cameron 68 Nova 396 E/S 68 Camaro SS/? ex Checkmate Modified |
![]() |
![]() |
![]() |
#17 |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]()
Today I finished my line hone, set housing bore to 2.4914. Next I will clean the block and set up for decking, assembly height:
Stroke 3.00 Rod length 5.698 Comp height. 1.800 Total height. 8.998 I need to decide which head gasket thickness I will use, then I will cut the block. Last edited by MIKE JONES 302; 09-03-2018 at 08:21 PM. |
![]() |
![]() |
Liked |
![]() |
#18 |
Senior Member
Join Date: Jun 2011
Location: Langley (no igloos), British Columbia, Canada
Posts: 555
Likes: 286
Liked 235 Times in 81 Posts
|
![]()
Mike Jones you are doing a fine job, keep the Build updates coming. It's great to see a young fellow developing an ability. Your combination of parts should workout just fine, keep it light and low drag. The preparation of all the components are important, but you appear to have that handled. Keep up the "GOOD WORK"… Maurice.
|
![]() |
![]() |
Liked |
![]() |
#19 | |
Junior Member
Join Date: Aug 2018
Location: Colorado Springs Colorado
Posts: 28
Likes: 2
Liked 85 Times in 15 Posts
|
![]() Quote:
|
|
![]() |
![]() |
Liked |
![]() |
#20 |
VIP Member
Join Date: Aug 2013
Posts: 1,766
Likes: 1,197
Liked 1,958 Times in 493 Posts
|
![]()
Very cool! Lots of great members here that's for sure.
__________________
Todd Greene |
![]() |
![]() |
![]() |
|
|