big bell or small bellhousing C4? - Page 2

Chris1529 · 04-04-2007, 12:32 PM

I also run the small bellhousing. 157 tooth w/tci flex plate.
Performance Automatic makes the spacer plate that works great. Make sure you get 50 oz balance componets.

I may be wrong, but if you use a case fill trans, you probably have to use the small bellhousing to get a dipstick to fit. I believe most of the large bellhousings came on the pan fill type.

Earle Holt · 04-06-2007, 04:09 PM

The flexplate should have a counterweight welded to it from the factory. (Not sure why yours wouldn't) From a transbrake perspective, I don't think it would matter what trans you use. The valve bodies are interchangable. I have both a small bellhousing C-4 that is case-filled and a large bellhousing C-4 that is pan filled and both worked fine.

Larry Munk · 04-07-2007, 08:36 AM

If you're only going to bracket race it put a powerglide in it. Lots cheaper in the long run.

Chris1529 · 04-07-2007, 02:07 PM

I would like to believe you are only joking about the powerglide.

Put and AOD in it and a 456 gear in the the rear end and drive it on the street also.

greg fulk · 04-07-2007, 04:46 PM

Well here's the "PLAN" ....I'm going to put on a set of E7TE heads that I have that have been ported. Add the C4 the 8.8 & let Marissa drive it /race it for a year or two. Then I'm going to let her buy her a new Mustang GT conv & I'm going to take the little car & make a GT/MA car out of it. That's the plan anyway.......

novamoation

Chris1529 · 04-09-2007, 07:44 AM

sounds like a good plan to me.

Chris1529 · 04-10-2007, 11:10 AM

Are you going to put the original 600 cfm Holley on it?

greg fulk · 04-10-2007, 08:23 PM

Yes sir!

novamoation

greg fulk · 04-11-2007, 12:21 PM

I've seen no pictures my Polhill! mgfulk@yahoo.com

novamoation

wsp · 04-14-2007, 01:13 PM

small...same as me

04-04-2007, 12:32 PM	#11
Chris1529 VIP Member Join Date: Dec 2006 Location: West Virginia Posts: 1,370 Likes: 6 Liked 58 Times in 28 Posts	I also run the small bellhousing. 157 tooth w/tci flex plate. Performance Automatic makes the spacer plate that works great. Make sure you get 50 oz balance componets. I may be wrong, but if you use a case fill trans, you probably have to use the small bellhousing to get a dipstick to fit. I believe most of the large bellhousings came on the pan fill type. __________________ Chris Bowman The Mountain State Mustang 1984 Mustang GT350

04-06-2007, 04:09 PM	#12
Earle Holt Member Join Date: Nov 2001 Posts: 194 Likes: 1 Liked 4 Times in 1 Post	The flexplate should have a counterweight welded to it from the factory. (Not sure why yours wouldn't) From a transbrake perspective, I don't think it would matter what trans you use. The valve bodies are interchangable. I have both a small bellhousing C-4 that is case-filled and a large bellhousing C-4 that is pan filled and both worked fine. __________________ Earle Holt 1055 Stock

04-07-2007, 02:07 PM	#14
Chris1529 VIP Member Join Date: Dec 2006 Location: West Virginia Posts: 1,370 Likes: 6 Liked 58 Times in 28 Posts	I would like to believe you are only joking about the powerglide. Put and AOD in it and a 456 gear in the the rear end and drive it on the street also. __________________ Chris Bowman The Mountain State Mustang 1984 Mustang GT350

04-07-2007, 04:46 PM	#15
greg fulk VIP Member Join Date: Jan 2003 Location: jackson Posts: 1,165 Likes: 0 Liked 5 Times in 3 Posts	Well here's the "PLAN" ....I'm going to put on a set of E7TE heads that I have that have been ported. Add the C4 the 8.8 & let Marissa drive it /race it for a year or two. Then I'm going to let her buy her a new Mustang GT conv & I'm going to take the little car & make a GT/MA car out of it. That's the plan anyway....... novamoation __________________ Greg Fulk 308 308X P/SA "ALL AMERICAN"

04-09-2007, 07:44 AM	#16
Chris1529 VIP Member Join Date: Dec 2006 Location: West Virginia Posts: 1,370 Likes: 6 Liked 58 Times in 28 Posts	sounds like a good plan to me. __________________ Chris Bowman The Mountain State Mustang 1984 Mustang GT350

04-07-2007, 08:36 AM	#13
Larry Munk Member Join Date: Nov 2001 Posts: 135 Likes: 0 Liked 1 Time in 1 Post	If you're only going to bracket race it put a powerglide in it. Lots cheaper in the long run.

04-10-2007, 11:10 AM	#17
Chris1529 VIP Member Join Date: Dec 2006 Location: West Virginia Posts: 1,370 Likes: 6 Liked 58 Times in 28 Posts	Are you going to put the original 600 cfm Holley on it? __________________ Chris Bowman The Mountain State Mustang 1984 Mustang GT350

04-10-2007, 08:23 PM	#18
greg fulk VIP Member Join Date: Jan 2003 Location: jackson Posts: 1,165 Likes: 0 Liked 5 Times in 3 Posts	Yes sir! novamoation __________________ Greg Fulk 308 308X P/SA "ALL AMERICAN"

04-11-2007, 12:21 PM	#19
greg fulk VIP Member Join Date: Jan 2003 Location: jackson Posts: 1,165 Likes: 0 Liked 5 Times in 3 Posts	I've seen no pictures my Polhill! mgfulk@yahoo.com novamoation __________________ Greg Fulk 308 308X P/SA "ALL AMERICAN"

04-14-2007, 01:13 PM	#20
wsp Junior Member Join Date: Apr 2007 Location: So.newhampshire Posts: 8 Likes: 0 Liked 0 Times in 0 Posts	small...same as me