Looking for a Holley Terminator X wiring expert.

[Cglrcng]

[Cglrcng]

The pics I posted so far, pic 1 (the Chrysler 5 pin Electronic Spark Control module and harness is from a 1983 Dodge Omni. (We took spark control away from the ECM/PM stock package and it currently is set at 46 degrees static all in all the time and runs happiest at that albeit very high setting. Have tried higher and lower.

It is harder starting, but never fails to fire up. I don't know if we can even use it w/ the Terminator X..more than willing to go to an MSD based Ign. Box if not but need best suggestion on what to buy if so.

The second pic is the Bosch upright throttle body w/ the 2 wire IAC on the rear of it (I have 2 of them, a brand new 1 is on the car now, and the stock 1 I have rebuilt and the following pics are the throttle body rear without the IAC attached showing the air passage ports top and bottom. I have 1 of the original Chrysler diagnostic tools which has a function setting wherein after plugging it into the ECM diagnostic connector at the passenger strut tower you can run through 5 cycles of each EFI function like IAC, injector firing, etc.

That 2 wire IAC when running the diag just cycles open /closed so very simple.

Really just need wiring pinnout there Hi/ Low?...the Holley wiring diagram calls for 4 wires. Or do we need to go PWM?

[Cglrcng]

The next set of pics is the 84 Turbo edition dual hall effect pick up distributor w/2 3 wire connectors (the 1distributo currently on the car has 1 -3 wire connector and 1 hall effect P.U. (Just top of the plate that is fired by the 4 blades under the rotor), the Turbo distro has 1 under as seen and that large 1 inside the distro body can be machined or trimmed easily enough if needed.

I only have 1 single injector and as Gump has pointed out to me we may not even need a double synch as long as the Holley ECU sees absolute TDC fir crank signal since it is single point injection?

On that distro, the pickup wires on each 3 wire connector(s) are red/green/black if the connector is cut off. The green wires are the centers w/ the white trace markings. The balance of the ]ics are the chrysler chrome box 5 pin elect. Control module and single Mallory coil.

I will get a new 5 pin connector if we can use the existing spark control module. If we switch to MSD then best unit to use I am up for recommendations before I buy it. I do want 2 step functions soon.

Next up I will find and resize and post the WBO2 pics am having issues on how to wire that up as there are 8 holley wires (7 plus the shield), then the WBO2 has actual 5 wires to a 6 pin connector-1 is not a pin. And the wire colors do not match between the shielded cable and the sensor. The 8 pin Deutch connector I will next install on the cable I have the diagram pinout locations on it, it is from the main harness connector (8 cavity),
to the 6 cavity female connector or do I need /should I buy the 8 to 6 conversion extender I saw at Summit for the 2.9 Bosch WBO2...or scrap it all and need the Holley WBO2 to solve that connection issue?

All other connections to all sensors have been accomplished. (Inputs/outputs, CAN, future dash if needed), fuel pump, relay, the main power for the Terminator X, fuses at the battery and at the mounted Term. X, MAP is internal, TPS, additional 2 Manifold ground points added & connected to the loose black main ground. Injector, Fuel Pressure, Oil Pressure, MAT, Water Temp, (engine does not have knock sensors, so those cavities in J1A were left unpopulated, plugged), car does have a speed sensor on it, I have not run anything to that sensor), I did not see any provision for that in the MPFI

[Cglrcng]

Wiring Diagram has no provision for it.

The original stock ECM/ PM is a (Speed Density based EFI system). Pretty crude, but worked simply by tables and on/off flag settings. The ECM coding at the time was never released per EPA regulations and nobody ever was able to burn performance chips for them as only the rebuilders had access. (I did get a look at a later 85 model turbo one that was hacked but just the tables could be viewed via a custom cable plugged into the diagnostic connector allowed access to change a few flags. A preset safety of the 84 TBI shuts off the injector at 4800 rpm in low gear only that I now know is triggered by the existing MAP sensor it a major limitation. I had a higher lift al lot of overlap and duration Reed cam in the car a year ago, that would have zero vacuum until 3,000 rpm where it just started building any vacuum allowed the engine to bypass that safety (no vacuum for the MAP sensor to trigger the ECM, and in low on an 1/8th mile legal street track setup allowed it to scream right up to 7K rpm in low gear. That cam was pulled out. But, getting rid of that safety w/ the Holley Term. X is the key. Currently short shifting 4,600/6,200 in D, to stay away from that injector cutoff safety that leads to a lean pop condition and massive loss of et if you get anywhere near exceeding 4,800 rpm in low gear only. That cure is what I need to finish installing. It runs great at sea level, at elevation tracks it is very rich, and Currently no provision or tuning capabilities to lean it out any further at elevation.

Ty for any input you may have on the ignition, IAC, and WBO2...and anything else I noted above. And if you need any other info I can provide it ASAP.

Thanks again Robin I appreciate any input or help you can provide in helping me with the completion and any other suggestions you may have to get the best options installed.

Gary.