LS/SBC parts - Wheels, Converters, misc

[JeffM]

Weld Alumastar 15 x 12 rear wheels with 4.75 pattern and 3” BS. $800.00. Very good condition, no screw holes

Precision Performance Products Kwik shift I manual shifter – excellent condition – no mounting plates. Black. 3 speed, push to shift with clean neutral. $350.00

TCI SBC/BBC lightweight 29.2 168T flexplate PN 399870LW, like new. Weighs 6.09lbs. Can barely see the contact patch on the starter ring. Original date was 1/19, but was only ran in the car for 2 races. Will need recertified. Excellent condition $300.00

Jesel Dogbone lifters LFD-44002 .842 Diameter – set of 16 – $800.00
LS Bryant crankshaft – 4” stroke – 58x - $2800

Carillo rods 6.1 rods (was used with Bryant crankshaft above)
BE :2.2253
PE :0.9285
Length: 6.100
B Width : 0.938
$1200.00

Forged small journal 327 GM crankshaft. Offset ground (.020 under) by Shaftech. 1.979 rods, 2.300 mains – 3.263 stroke $750.00

Oliver I beam 5.7 rods set of 8 (was used with Shaftech crank above)
BE: 2.125
PE: 928
Length: 5.7
Weight each: 575 Grams
$800.00

8” ATI converter - Flashed 6500 behind 427/430 LS Combo –Powerglide spline - $500

7" Converter - Dynamic. Powerglide input, flashed 7000 behind 327/275 hp combo. - $500.00

Wilson 1” 4 hole aluminum tapered spacer – Dominator flange PN 024110 - $150 used for test only

6.00 12 bolt ring and pinion. Ring gear has been backcut - less than 10 runs $250.00

Polished fabricated valve covers with baffles tall - $100.00

Manley 221443P-16 valve springs with 23648-16 Ti - retainers, locks and 42573-16 locators (run on dyno) $300 for set.

ATI balancer pulley PN 916794 4 groove aluminum 6.430 diameter - New $40.00
ATI balancer pulley PN 916732 4 groove aluminum 6.430 diameter – used $50.00

CV products 3/8 pushrods (qty 18) 9.200 x .080 x 5/16 ends – used but good condition – $30.00
Trend 3/8 pushrods (qty 16) 7.450 x .135 x 5/16 ends – used but good condition) $50
Trend 7/16 tapered pushrods (qty 16) 9.400 x .165 x 5/16 ends new - $150
Trend 3/8 pushrods (qty 8) 9.400 x .135 x 5/16 ends used - $25
Trend 3/8 pushrods (qty 8) 9.450 x .135 x 5/16 ends used - $25
Trend (qty 17) – 9.150 DBL taper .135 wall pushrods 5/16 ends (used good) $35
Trend 9.400 DBL taper .135 wall pushrods 5/16 ends (11) new $150
Trend 9.300 DBL taper .135 wall pushrods 5/16 ends (11) new $150

JRI 2010-2015 Camaro front struts $500.00 used.

1 – Lingenfelter billet steel LS block girdle, No hardware $500
2 GM truck oil pans (1999-2006) pan only $50.00 each

Pit Pal Pit Ramps 280 with vertical storage pouch for trailer
Aluminum, 24.00 in. Length, 8.00 in. Width, 2.75 in. Height, Pair with pouch $200

Jerry Bickel Pit ramps and trailer pouch $120.00

Can bring to Norwalk National event

260-223-0157
superstock@live.com

[BZenzen]

Hi Jeff, is the shifter for a TH 350? FWD or Reverse valve body? Thanks!

[JeffM]

Originally Posted by BZenzen

Hi Jeff, is the shifter for a TH 350? FWD or Reverse valve body? Thanks!

Any 3 speed transmission with clean neutral all the way forward. Push to shift. Park is all the way in the rear P, R,1,2,3,N. Cable exits in the rear.